Skoda Felicia

Since 1994 of release

Repair and car operation



Shkoda Felitsija
+ Cars of mark Skoda Felicia
+ The maintenance instruction
+ Routine maintenance
+ Engine repair
+ Systems of cooling, heating
+ The power supply system
+ Engine electric equipment
- Coupling
   The general information
   Removal and installation of a pedal of coupling
   Removal, installation and adjustment of a cable of a drive of coupling
   Removal, check of a condition and installation of assemblage of coupling
   Removal, check of a condition and installation of the mechanism of deenergizing of coupling
+ Transmission
+ Power shafts
+ Brake system
+ Suspension bracket and steering
+ Body and salon furnish
+ Onboard electric equipment


c9b0dd5c

Removal and installation of a pedal of coupling

Components of a pedal of coupling

1 — a cable Clamp
2 — the Cable of a drive of coupling
3 — a coupling Pedal


4 — the Spring
5 — an axis Clamp


Models with a right-hand steering

Performance of replacement of axial plugs of a pedal of coupling is possible without dismantle of pedal assemblage, despite the extremely limited access. Take шплинты from both parties of an axis of a pedal and shift back persistent washers, providing possibility of extraction of axial plugs from the landing nests and their removal from an axis. New plugs before installation grease with universal greasing of type Litol 24 or G00062 (ask in shops automobile химикалиев). Having planted both plugs in the reception nests, establish into place persistent washers and fix assemblage new шплинтами. In summary do not forget to make adjustment drive a coupling cable (see Has undressed Removal, installation and adjustment of a cable of a drive of coupling).

REMOVAL

 PERFORMANCE ORDER

1. Components of pedal assemblage are presented on an accompanying illustration.
2. In an impellent compartment disconnect a negative wire from the battery, then find трансмиссионный the end drive a cable of coupling and completely release an adjusting nut, having provided the maximum weak point of a cable.
3. Remove the central console (see Has undressed Removal and installation of the central console).
4. Remove the radio receiver block, then unbend back lock uvulas and take a frame of a radio tape recorder from a reception nest in the panel of devices. Disconnect an antenna cable and electroconducting, then definitively remove a frame.

5. Release clamps and remove a sleeve connecting a casing of a heater with a back foot well.

6. Disconnect from a coupling pedal an auxiliary spring. Under the panel of devices remove a fastening clamp drive a cable to a pedal. Liberate from a pedal a cable tip.

7. Disconnect приводной a cable from the top part of a pedal of an accelerator.

8. Disconnect electroconducting from the gauge-switch of stoplights which will screw in the top part of the right arm of pedal assemblage.

9. In a passenger foot well take a plastic clamp and remove from the left arm of pedal assemblage the decorative panel.

10. Remove a clamp and liberate from a pedal a tip of fastening of draught of a pusher of the servo-driver of the vacuum amplifier of brakes.

11. Give fixing nuts and remove an emphasis of a pedal of an accelerator and a foot emphasis on the left side of a coupling pedal.

12. Release clamps and roll a carpet covering on a partition of an impellent compartment, having provided access to the bottom nuts of fastening of a pedal arm.

13. Give nuts of fastening of the left and right arms of pedal assemblage. Take from an impellent compartment the bottom basic plates.

14. Accurately take pedal assemblage from the car.
15. Having laid assemblage on a workbench, cautiously unhook a returnable spring of a brake pedal from a back part of the lever of the servo-driver. Take lock rings of fastening of an axis of a brake pedal and remove from pedal assemblage basic arms, axial plugs and a returnable spring. The further dismantling is not represented possible. Coupling and brake pedals are delivered by uniform assemblage (in an individual order axial plugs are subject to replacement only and шплинты - the remark in the Section beginning see).

INSTALLATION

 PERFORMANCE ORDER

Installation is made upside-down Special attention it is necessary to give to following moments:

a) do not forget to grease before installation axial plugs of pedal assemblage by universal greasing (the remark in the Section beginning see);
b) Having connected to a pedal an accelerator cable, check up correctness of its adjustment;
c) After connection drive a coupling cable, make its adjustment according to the instructions resulted in Section Removal, installation and adjustment of a cable of a drive of coupling;
d) In summary connect the battery and check up serviceability of functioning of stoplights.


Models with a link sided steering

REMOVAL

 PERFORMANCE ORDER

1. In an impellent compartment disconnect a negative wire from the battery, then find трансмиссионный the end drive a cable of coupling and completely release an adjusting nut, having provided the maximum weak point of a cable.
2. Disconnect from a coupling pedal an auxiliary spring. Under the panel of devices remove a fastening clamp to a pedal drive a cable. Liberate from a pedal a cable tip.
3. Remove a clamp from the end of an axis of a pedal, shift a pedal from the place and remove it from a basic arm complete with an auxiliary spring.
4. Check up a pedal on presence of signs of deterioration and mechanical damages. In case of need make replacement. The axial plug of a pedal serves also for landing of a brake pedal. If the plug requires replacement, it is necessary to take care of reliable fixing of a pedal of a foot brake for the period of performance of procedure of extraction of the old plug and installation new.

INSTALLATION

 PERFORMANCE ORDER

1. Establish on a pedal an auxiliary spring, grease an axis of a pedal and the plug with universal greasing (the remark in the Section beginning see).
2. Get a pedal on the regular place, having tracked correctness of installation of an auxiliary spring. Fix assemblage by a clamp.
3. Grease a tip drive a cable with universal greasing and connect it to a pedal, having fixed a clamp.
4. Connect to a pedal a returnable spring, then execute adjustment drive a coupling cable (see Has undressed Removal, installation and adjustment of a cable of a drive of coupling). In summary connect a negative wire to the battery.