Skoda Felicia

Since 1994 of release

Repair and car operation



Shkoda Felitsija
+ Cars of mark Skoda Felicia
+ The maintenance instruction
+ Routine maintenance
+ Engine repair
+ Systems of cooling, heating
+ The power supply system
+ Engine electric equipment
+ Coupling
- Transmission
   The general information
   The description of knots and mechanisms
   Removal and installation of draughts of a drive of a gear change
   Replacement of epiploons
   Check of serviceability of functioning, removal and installation of the gauge-vyklju-chatelja of fires of a backing
   Removal and installation of the mechanism of a drive of a speedometer
   Removal and transmission installation
   Major repairs РКПП, dismantling and assemblage of knots and components
+ Power shafts
+ Brake system
+ Suspension bracket and steering
+ Body and salon furnish
+ Onboard electric equipment


c9b0dd5c

The general information

Gear change box - appearance

1 — the Gauge-switch of fires of a backing
2 — the Sealing ring
3 — Carter of a transmission
4 — the Screw (10 Nanometers)
5 — the Lock washer
6 — the Peak
7 — the Directing pin
8 — Hairpin М10 (50 Nanometers)
9 — the Ventilating tube
10 — the Stopper
11 — Zaglushka
12 — the Hairpin (50 Nanometers)
13 — Carter (dome) of coupling

14 — the Hairpin (50 Nanometers)
15 — the Screw
16 — the Magnet
17 — the Nut (35 Nanometers)
18 — the Screw (25 Nanometers)
19 — the Sealing ring (at assemblage is subject to replacement)
20 — the Carving stopper of a drain aperture (60 Nanometers)
21 — the Screw (10 Nanometers)
22 — the Persistent ring
23 — the Lock screw (35 Nanometers)
24 — the Stopper
25 — the Oil trench


Assemblage of a box gear changes (check point) is placed in cast aluminium картер, приболченный to the left end face of the engine. The assemblage structure includes mechanisms actually transmissions, and also differential of the main transfer.

Rotation is transferred from a cranked shaft of the engine through coupling assemblage to the primary shaft РКПП equipped extended and equipped шлицами with a pin which is passed in a nave of a frictional disk of coupling. The primary shaft of a box rotates in not folding ball-bearings placed in the tight case. From a primary shaft rotation is transferred to a secondary shaft of the box which right end is passed in the roller bearing, and left - in the tight ball-bearing. The target end of a secondary shaft of a box is entered into gearing with корончатой a conducted gear wheel of the main transfer rigidly connected to a box of differential in which there is a planetary assemblage. From lateral gear wheels of differential rotation is transferred further to power shafts and further - on leading forward wheels of the car. Gear wheels of satellites are freely planted on the axis that provides possibility of rotation of driving wheels of the car with various speed, completely eliminating thereby probability of proslipping of an internal wheel during fulfilment of maneuvers.

Primary and secondary shaft of a transmission are located in parallel each other, and also to in parallel cranked shaft and power shafts of the leading bridge. In view of feature of a configuration of a gear wheel of both shaft constantly are in gearing with each other. On neutral transfer of a gear wheel rotate on secondary to a shaft freely, without transferring rotation to a conducted gear wheel of the main transfer.

The gear change is carried out by means of the salon of control lever РКПП established on a floor and means drive the mechanism of a choice of transfers. The drive of the mechanism of a choice of transfers consists of a set of plugs of switching with which help sliding муфты synchronizers move along a shaft, carrying out blocking of gear wheels of corresponding transfers with the naves. As naves sliding муфт are equipped шлицами, entered into gearing with reciprocal шлицами the secondary shaft, the gear wheel blocked on a nave starts to rotate together with shaft, providing the further drive with the corresponding transfer relation. For a guarantee of speed and quality of a gear change in a box synchronisation of all forward transfers is provided. Synchronisation is provided at the expense of application of blocking rings with подпружиненными sliding keys and naves of synchronizers with gear wheels. Cones of synchronizers provide surfaces of interface of blocking rings with gear wheels. More in detail a principle a design and functioning РКПП are described in Section a system Design, the description of separate knots and mechanisms.