Skoda Felicia

Dump pressure in a fuel tank (see Has undressed Dump of residual pressure in the power supply system), then disconnect a negative wire from the battery.

1. Remove the top covers of the case of a throttle and an air cleaner (see Has undressed Removal and installation of assemblage of an air cleaner).
2. Disconnect a cable of an accelerator from the lever of a drive throttle заслонки (see Has undressed Removal, installation and adjustment of a cable of an accelerator). Liberate a cable from a basic clamp and take him aside.
3. Disconnect electroconducting from the module of position throttle заслонки and the gauge of temperature/pressure of soaked up air.
4. Disconnect a hose going from a coal adsorber, and also the small vacuum hose going from a cover of a head of cylinders from the case of a throttle.
5. Carefully having marked wires, disunite electric sockets. Liberate burn down electroconductings from clamps on the top party of a fuel highway and take him aside.
6. Disconnect a vacuum hose from a forward part of a regulator of pressure of fuel
7. Enclose under штуцерные connections of lines of giving and fuel return on a fuel highway old rags. Release collars and disconnect hoses of lines from a highway. Try to remember adjusting position of hoses - submitting settles down more close to the throttle case.
8. "Walk" on a vacuum hose from the impellent compartment established on a partition to the block of the servo-driver of the brake amplifier to the union on a left-hand side of the inlet pipeline. Remove a hose from the union.

9. Отболтите a basic rack from the right wall of the inlet pipeline.

10. Make sure that nothing remains connected to the pipeline and does not disturb to its removal.

11. In stages ослабьте six fixing nuts and bolts (access to four of them is possible from above, to two - from below). Try not to mix fixture of the inlet pipeline with fixture of a final collector. Separate the pipeline from a head of cylinders and take it from an impellent compartment - try not to admit вытекания from a fuel highway of the rests of fuel. Remove and will throw out two linings - at assemblage they are subject to replacement without fail.

1. Remove the top covers of the case of a throttle and an air cleaner (see Has undressed Removal and installation of assemblage of an air cleaner).
2. Disconnect a cable of an accelerator from the lever of a drive throttle заслонки (see Has undressed Removal, installation and adjustment of a cable of an accelerator). Liberate a cable from a basic clamp and take him aside.
3. Disconnect electroconducting from the module of position throttle заслонки and the gauge of temperature/pressure of soaked up air. Disconnect a hose going from a coal adsorber from a forward wall of the case of a throttle.
4. Carefully having marked wires, disunite electric sockets. Liberate burn down electroconductings from clamps on the top party of a fuel highway and take him aside.
5. Disconnect a vacuum hose from the union on the bottom part of a regulator of pressure of fuel
6. Enclose under штуцерные connections of lines of giving and fuel return on a fuel highway old rags. Release collars and disconnect hoses of lines from a highway. Try to remember adjusting position of hoses - submitting settles down more close to the throttle case.

7. Disconnect the vacuum hose going from the servo-driver of the brake amplifier from the union on the left wall of the inlet pipeline.

8. In stages ослабьте also turn out bolts of fastening of the inlet pipeline to a head of cylinders. Separate the pipeline from a head and take it from an impellent compartment - try not to admit вытекания from a fuel highway of the rests of fuel. Remove and will throw out two sealing rings - at assemblage they are subject to replacement without fail.

Installation is made upside-down. Pay attention to following moments:

a) Sealing linings/rings are subject to replacement without fail;
b) All fixture should be tightened with demanded effort;
c) Track quality of all шланговых and electric connections;
d) do not forget to adjust an accelerator cable (see Has undressed Removal, installation and adjustment of a cable of an accelerator);
e) Before to start car operation, carefully check up the power supply system on presence of signs of leaks.