Skoda Felicia

Since 1994 of release

Repair and car operation


Shkoda Felitsija
+ Cars of mark Skoda Felicia
+ The maintenance instruction
+ Routine maintenance
+ Engine repair
+ Systems of cooling, heating
- The power supply system
   + The power supply system of the carburettor engine of 1.3 l
   + System of the central injection (SPFI) the petrol engine
   - System of the distributed injection (MPFI) the petrol engine
      The general information and safety measures
      Removal and installation of assemblage of an air cleaner
      Control mean in temperature of soaked up air - the general information
      Removal, installation and adjustment of a cable of an accelerator
      Removal and installation of components of system of injection Simos 2P
      Removal and installation of components of system of injection Magneti-Marelli 1AV
      Removal and installation of assemblage of the fuel pump and the gauge of measurement of the expense of fuel
      Removal and installation of a fuel tank
      Dump of residual pressure in the power supply system
      Removal and installation of the inlet pipeline
      Check of serviceability of functioning and adjustment of system of injection
      Neetilirovannoe fuel - the general information and use rules
   + The power supply system of the diesel engine
   + Systems of decrease in toxicity and release of the fulfilled gases
+ Engine electric equipment
+ Coupling
+ Transmission
+ Power shafts
+ Brake system
+ Suspension bracket and steering
+ Body and salon furnish
+ Onboard electric equipment

c9b0dd5c

Removal and installation of assemblage of an air cleaner

REMOVAL

Components of assemblage of an air cleaner (model 1.6)

1 — Screws of fastening of a cover of the case of a throttle
2 — the Cover of the case of a throttle
3 — the Reception knee of a sleeve of giving of air
4 — the Branch pipe сапуна
5 — the Sealing lining
6 — the Sleeve of giving of air
7 — the Top cover of an air cleaner

8 — the Filtering element
9 — an air cleaner Casing
10 — an air inlet Sleeve
11 — the Nozzle
12 — the Sleeve of giving of the warmed-up air
13 — the Plastic nut
14 — the Casing of the device of heating of soaked up air


L models 1.3

 PERFORMANCE ORDER

1. Release located on perimetre of the top cover of an air cleaner wire clamps.

2. Turn out three bolts from a cover of the case of a throttle, then liberate from clamps on the bottom party of a cover a hose going to a coal adsorber, and electroconducting plaits.

3. Disconnect from a cover of a head of cylinders a branch pipe ventilating сапуна...

Also liberate from a clamp under an inlet air line a vacuum hose of a regulator of pressure of fuel.

4. Uncover throttle cases together with the top cover of an air cleaner and an inlet air line.


L models 1.6

 PERFORMANCE ORDER

1. Turn out three screws from a cover established on the cases of a throttle. Pay attention that the forward screw is longer than other two.

2. Liberate from clamps on the bottom party of a cover of the case of a throttle all hoses and electroconducting plaits. Lift a cover.
3. Release four wire clamps, located on perimetre of the top cover of an air cleaner.
4. Disconnect from the top part of a reception knee of a sleeve of giving of air a ventilating branch pipe. Liberate from clamps and shift aside all disturbing to removal of a knee of a wire and hoses.
5. Turn out three fixing screws and remove a knee of a sleeve of giving of air together with a sleeve and the top cover of an air cleaner.


All models

 PERFORMANCE ORDER

1. At a corresponding complete set, check up a condition of the rubber sealing lining established from above on the cases of a throttle. In case of need make replacement.

2. In need of removal of a casing of an air cleaner from a mudguard of a wheel arch, take filtering element and disconnect from the basis of a casing a sleeve of giving of the warmed-up air.

3. The casing fastens a plastic nut in front. Two lateral rubber support are inserted into apertures in a mudguard of a wheel arch.

4. Give a nut, liberate support from a mudguard and take a casing from an impellent compartment.

5. The management valve заслонкой devices of giving of the warmed-up air can be removed after отдавания two fixing screws in a forward part of a casing.

INSTALLATION

 PERFORMANCE ORDER

Installation is made upside-down. The rubber sealing lining of the case of a throttle should provide full air hermetic sealing - the slightest thinness of a joint can essentially affect stability of turns of the engine.