Skoda Felicia

Since 1994 of release

Repair and car operation



Shkoda Felitsija
+ Cars of mark Skoda Felicia
+ The maintenance instruction
+ Routine maintenance
+ Engine repair
- Systems of cooling, heating
   The general information and safety measures
   Detachment and replacement of hoses of system of cooling
   Removal, check of a condition and radiator installation
   Removal, check of serviceability of functioning and thermostat installation
   Check of serviceability of functioning, removal, installation, dismantling and assemblage of the fan of system of cooling
   Check of serviceability of functioning, removal and installation of electric switches and gauges of system of cooling
   Removal, installation, dismantling and assemblage of the water pump
   System of heating/ventilation of salon - the general information
   Removal and installation of components of system of heating/ventilation of salon
   Air central air - the general information and safety measures
   Removal and installation of components of a central air of air
+ The power supply system
+ Engine electric equipment
+ Coupling
+ Transmission
+ Power shafts
+ Brake system
+ Suspension bracket and steering
+ Body and salon furnish
+ Onboard electric equipment


c9b0dd5c

Removal, check of serviceability of functioning and thermostat installation

The thermostat and accompanying components

1 — From a broad tank
2 — the Bolt
3 — the Fixing arm
4 — To a radiator
5 — CTS (the temperature gauge)
6 — the Sealing ring (is subject to replacement)
7 — the Sealing ring (is subject to replacement)

8 — the Drain stopper
9 — To the heater heat exchanger
10 — the Gauge of temperature of a cooling liquid of system of injection
11 — the Nut
12 — a thermostat Casing
13 — the Thermostat


REMOVAL

 PERFORMANCE ORDER

1. Thermostat components are shown on an illustration.
2. Disconnect a negative wire from the battery, then empty cooling system.


Petrol models

 PERFORMANCE ORDER

1. The thermostat casing is established in the left part of a head of cylinders.

2. Release a fixing collar () and disconnect a hose () охладительного a path from a thermostat cover.

3. Turn out fixing boats

Also remove from the engine a thermostat cover together with a sealing ring/lining. At assemblage the ring/lining is subject to replacement without fail.

4. On models 1.3 of l of early years of release (till February, 1996) and on all models 1.6 of l take the thermostat from a casing. Try to remember its adjusting position.

5. On models 1.3 of l of late years of release (since February, 1996) thermostat assemblage fastens in a casing cover a special clamp. Remembering adjusting position of each component, release a clamp,

Remove a spring

Also take from a cover плунжер the thermostat.


Diesel models

 PERFORMANCE ORDER

1. The thermostat is established in the basis of the case of the water pump. For the purpose of providing of access cock a lay brake, then поддомкратьте redock of the car and establish it on props. Give fixing screws remove the protection panel картера.

2. Release a collar and disconnect a hose охладительного a path from a thermostat cover.

3. Turn out fixing bolts and remove from a casing of the thermostat a cover together a sealing ring. The ring at assemblage is subject to replacement without fail.

4. Having uncovered, take from a casing thermostat assemblage. Try to remember its adjusting position.


Check of serviceability of functioning

 PERFORMANCE ORDER

On models 1.3 of l of late years of release (since February, 1996) check is carried out after installation of components in a cover of a casing of the thermostat.

1. Rough check of serviceability of functioning of the thermostat can be made a way подвязывания it to a wire and lowerings in capacity with water. In process of heating at boiling of water the thermostat valve should open, otherwise it is necessary to make assemblage replacement.
2. If available there is a suitable thermometer, it is possible to define exact temperature of opening of the thermostat - compare result of measurement to the marks data on the case of assemblage or requirements of Specifications in the beginning of the present chapter.
3. The thermostat which is not closed at cooling of water, also is subject to replacement.

INSTALLATION

Petrol models

 PERFORMANCE ORDER

1. On models 1.3 of l of late years of release (since February, 1996) establish in a casing cover плунжер the thermostat with a spring, then latch a clamp.
2. On models 1.3 of release till February, 1996 and l models 1.6 establish the thermostat in a casing (track for correctness of an arrangement of assemblage).
3. On all models establish a new sealing ring/lining, then plant a thermostat cover on a casing and tighten bolts of its fastening with demanded effort.
4. Connect to a cover of the thermostat a hose () охладительного a path, strongly tighten a collar ().
5. Fill system of cooling and connect a negative wire to the battery.


Diesel models

 PERFORMANCE ORDER

1. Establish on a thermostat cover a new sealing ring.
2. Enclose thermostat assemblage in a casing (track correctness of its installation), then plant a cover. Screw fixing bolts and tighten them with demanded effort.
3. Connect a hose охладительного a path and fix its collar.
4. Establish into place protection картера, strongly tighten fixing screws, then lower the car on the earth.
5. Fill system of cooling and remove from it air stoppers and connect a negative wire to the battery.