Skoda Felicia

1. Empty cooling system. The water pump is built in assemblage of the right support of the power unit.
2. Remove air cleaner assemblage.
3. Remove a belt of a drive of auxiliary units.

4. Turn out a bolt of fastening of a tube охладительного a path to the right end face of the engine, then release a fixing collar and disconnect a tube from a hose of pump assemblage.

5. From outside transmissions disconnect a rod of a choice of transfers, then release a collar for the purpose of providing of access to a cylindrical pin. The firm collar will replace at assemblage more correctly more convenient standard. Beat out a cylindrical pin (at assemblage it is subject to replacement without fail).

6. Turn out a bolt of fastening of a bar of the mechanism of a gear change to block RKPP, remove washers and a rubber pillow of a support.
7. Get a jack on the engine (between a head of a jack and the pallet картера for the purpose of loading distribution it is necessary to lay the wooden block) and slightly raise the power unit. Alternatively, hang out the unit from above with the help лебедки or beams.
8. Give a nut and remove a through bolt of a back support of the power unit.
9. Give a nut and take a through bolt of the right support. For the purpose of maintenance of sufficient working space for bolt extraction, remove заглушку the right mudguard. The bolt acts in film then through opened aperture and is taken through an arch of the right wheel.
10. Mark position of an arm of the right support of the power unit in relation to a car body, then turn out fixing bolts and remove an arm.

11. Give two nuts of fastening of assemblage of the water pump with a support to the block of cylinders. Remove assemblage from fixing hairpins and take it from the car, as required correcting height of suspension of the unit, trying not to admit excessive pressure on components of system of release of the fulfilled gases and вытягивания plaits of electroconducting and hoses.

12. Remove a sealing lining. At assemblage it is subject to replacement without fail.

2. Establish assemblage of a casing of the pump on the block of cylinders and tighten with demanded effort fixing nuts.
3. Establish on the regular place an arm of the right support of the power unit and screw fixing bolts. Achieve combination of the landing labels put in the course of dismantle, then tighten bolts with demanded effort.
4. Level the right support concerning an arm, insert a through bolt and screw a nut, having tightened it while only by hand. Establish in a mudguard of the right wing заглушку.
5. Establish a through bolt of a back support of the power unit, screw a nut and slightly tighten it.
6. Lower the engine. Slightly shake the unit on purpose усадки components, then tighten fixture of both support with demanded effort.
7. Clean a carving of a bolt of a bar of a gear change, completely having removed from coils all traces of old hermetic. Make sure of correctness of placing of rubber pillows and washers, then connect a bar картеру РКПП. Slightly grease a carving of a bolt with type hermetic. Loctite 270 or Three Bond 1305). Screw a bolt and tighten it with demanded effort (the Transmission see the Head).
8. Connect to a box a rod of a choice of transfer fix its cylindrical pin. Fix a pin a collar.
9. Connect a tube охладительного a path and fix its bolt, having tightened last with demanded effort. Strongly tighten a collar of fastening of a tube in a hose.
10. Establish a belt of a drive of auxiliary units (engine Repair see a corresponding Part of the Head).
11. Establish air cleaner assemblage.
12. Establish protection картера, strongly tighten screws of its fastening, then lower the car on the earth.
13. Fill cooling system.

1. Remove a belt of drive ГРМ with натяжителем (engine Repair see a corresponding Part of the Head).
2. Empty cooling system.

3. Turn out two bolts of fastening of the water pump...

... Also remove from the last a back cover газораспределительного a belt.

4. Remove the pump from the block of cylinders. Also remove a sealing ring which at assemblage is subject to replacement without fail.

2. Establish into place a belt of drive ГРМ (engine Repair see a corresponding Part of the Head).
3. In summary fill cooling system.

1. Empty cooling system.
2. Remove the generator.
3. Without disconnecting hydraulic lines, отболтите the steering pump from the support (the Suspension bracket and a steering see the Head) and shift it aside from the case of the water pump.
4. Turn out a bolt of fastening of back arm ТНВД to the top part of assemblage of a casing of the water pump/arm of a support of the power unit.
5. Release fixing collars and disconnect hoses охладительного a path from a back part of assemblage of the pump/arm of a support.

6. Turn out fixing bolts and remove assemblage of the pump/arm of a support from a forward part of the block of cylinders. Remove the sealing ring established between a casing and the block. At assemblage the ring is subject to replacement without fail.

7. Lay assemblage on a workbench, turn out fixing bolts and remove from the pump a pulley. Give bolts and remove the pump from a casing. Will throw out a sealing ring - at assemblage it should be replaced.

1. Make sure of absoluteness of cleanliness and dryness of interfaced surfaces of the pump and a casing, establish a new sealing ring.
2. Establish the pump on a casing and in regular intervals tighten fixing bolts with demanded effort. Establish a pulley and tighten with demanded effort bolts of its fastening.

	3. Enclose a new sealing ring in a flute of assemblage of a casing, then establish a casing on the block of cylinders, screw fixing bolts and tighten them with demanded effort in that order.

4. Connect to a casing hoses охладительного a path and strongly fix their collars.
5. Establish on the regular places the generator, the water pump and a belt of a drive of auxiliary units.
6. In summary fill cooling system.