Skoda Felicia

Since 1994 of release

Repair and car operation


Shkoda Felitsija
+ Cars of mark Skoda Felicia
+ The maintenance instruction
+ Routine maintenance
+ Engine repair
+ Systems of cooling, heating
- The power supply system
   + The power supply system of the carburettor engine of 1.3 l
   - System of the central injection (SPFI) the petrol engine
      The general information and safety measures
      Removal and installation of assemblage of an air cleaner
      The vacuum switch of a control mean in temperature of soaked up air
      Removal, installation and adjustment of a cable of an accelerator
      Removal and installation of components of system Bosch Mono-Motronic
      Removal and installation of assemblage of a gasoline pump and the gauge of the expense of fuel
      Removal and installation of a fuel tank
      Dump of residual pressure in the power supply system
      Removal and installation of the inlet pipeline
      Check of functioning and adjustment of system of injection
      Neetilirovannoe fuel - the general information and use rules
   + System of the distributed injection (MPFI) the petrol engine
   + The power supply system of the diesel engine
   + Systems of decrease in toxicity and release of the fulfilled gases
+ Engine electric equipment
+ Coupling
+ Transmission
+ Power shafts
+ Brake system
+ Suspension bracket and steering
+ Body and salon furnish
+ Onboard electric equipment

c9b0dd5c

Removal and installation of the inlet pipeline

Components of the inlet pipeline

1 — the Basic flange of the case of a throttle
2 — the Fixing bolt
3 — the Inlet pipeline
4 — the Nut of fastening of the inlet pipeline
5 — a hose Going to a heater охладительного a path

6 — the Gauge of temperature of a cooling liquid of system of injection
7 — the Union of connection of a vacuum hose of a cover of a head of cylinders
8 — the Union of connection of a vacuum hose of the amplifier of brakes
9 — Going to a casing of the thermostat a hose охладительного a path


The preventions resulted in Section the General information and safety measures see.

REMOVAL

 PERFORMANCE ORDER

1. Disconnect a negative wire from the battery.
2. Merge from the engine a cooling liquid. Alternatively, disconnect a negative wire from the battery. One of hoses охладительного a path from a back part of the inlet pipeline also empty the pipeline.
3. Disconnect electroconducting and fuel hoses from assemblage of the gauge of the expense of fuel (see Has undressed Removal and installation of components of system Bosch Mono-Motronic). Alternatively, remove entirely assemblage of the case of a throttle.
4. Release collars and disconnect hoses охладительного a path from the inlet pipeline.
5. Disconnect a hose of the vacuum amplifier of brakes from the union on the inlet pipeline.

6. Disconnect electroconducting from the gauge of temperature of a cooling liquid in a back part of the inlet pipeline.

7. Directly over the temperature gauge disconnect the vacuum tube going to a cover of a head of cylinders.

8. Turn out a fixing bolt and disconnect a tube of sampling WITH from a back part of the inlet pipeline.

9. All cables and hoses should be liberated from the clamps on a body of assemblage of the inlet pipeline. Try to remember routes of a lining of plaits and lines.

10. In stages give nuts of fastening of the inlet pipeline, then accurately separate the pipeline from a head of cylinders. Try not to damage a lining if its further use is supposed.

11. Last time make sure that nothing remains is connected to the pipeline, then take assemblage from an impellent compartment. In case of need the basic flange of the case of a throttle can be removed the pipeline after отдавания fixing nuts.
12. The damaged lining is subject to replacement. If the engine is equipped by the combined assemblage of the inlet pipeline / a final collector, it is necessary also the collector is removed also.

INSTALLATION

 PERFORMANCE ORDER

Installation is made upside-down. Pay attention to following moments:

a) Track cleanliness of interfaced surfaces of the pipeline and a head of cylinders;
b) Nuts of fastening of the pipeline should be tightened with demanded effort;
c) Track correctness of a lining and connection of all cables and hoses;
d) If removed, establish into place the throttle case (or connect corresponding electroconducting and hoses);
e) In summary add a liquid in cooling system.