Skoda Felicia

Since 1994 of release

Repair and car operation

Shkoda Felitsija
+ Cars of mark Skoda Felicia
+ The maintenance instruction
+ Routine maintenance
+ Engine repair
+ Systems of cooling, heating
- The power supply system
   + The power supply system of the carburettor engine of 1.3 l
   - System of the central injection (SPFI) the petrol engine
      The general information and safety measures
      Removal and installation of assemblage of an air cleaner
      The vacuum switch of a control mean in temperature of soaked up air
      Removal, installation and adjustment of a cable of an accelerator
      Removal and installation of components of system Bosch Mono-Motronic
      Removal and installation of assemblage of a gasoline pump and the gauge of the expense of fuel
      Removal and installation of a fuel tank
      Dump of residual pressure in the power supply system
      Removal and installation of the inlet pipeline
      Check of functioning and adjustment of system of injection
      Neetilirovannoe fuel - the general information and use rules
   + System of the distributed injection (MPFI) the petrol engine
   + The power supply system of the diesel engine
   + Systems of decrease in toxicity and release of the fulfilled gases
+ Engine electric equipment
+ Coupling
+ Transmission
+ Power shafts
+ Brake system
+ Suspension bracket and steering
+ Body and salon furnish
+ Onboard electric equipment


Removal and installation of assemblage of a gasoline pump and the gauge of the expense of fuel

The preventions resulted in Section the General information and safety measures see.

Avoid fuel hit on open sites of a skin - use protective gloves. Work carry out only in well ventilated premise.

The general information

The fuel pump is united with the gauge of the expense of fuel in the uniform assemblage established in the top part of a fuel tank. Access to assemblage is provided by removal of a cover specially provided лючка in the floor panel in a car luggage space. Assemblage is lowered in a fuel tank that is why its removal is interfaced to hit of a flying phase of a contained tank in atmosphere.



1. Dump residual pressure in the power supply system (see Has undressed Dump of residual pressure in the power supply system).
2. Make sure that the car is parked on an equal horizontal platform, then disconnect a negative wire from the battery.
3. Combine forward a back seat of the car and remove a decorative cover of the panel of a floor.

4. Turn out fixing screws and uncover лючка access to assemblage of the fuel pump/gauge of the expense of fuel in the floor panel.

5. Disunite an electroconducting socket in the top part of assemblage.

6. Impose with rags штуцерные connections of hoses of giving and fuel return, then ослабьте collars and disconnect hoses from the top part of assemblage. Do not forget to mark hoses as their connection - on unions special labels in the form of the arrows specifying a direction of a stream are provided.

7. Turn away a plastic ring of fastening of assemblage in an aperture of a fuel tank.

8. For отпускания байонетного a clamp turn assemblage on the left, then take it from a tank...

.... Preliminary having waited runnings off in it of the fuel rests. Remove a rubber sealing lining.

Отдавание a plastic fixing ring can be made by means of sliding nippers for water armature.

9. Take assemblage of the pump with датчикомиз the car and lay on sheet of cardboard well absorbing a moisture or the spread rags. Check up a float on the end of the lever of the gauge on presence of punctures and signs проникания in it of fuel - the damaged float is subject to replacement.
10. Assemblage is equipped подпружиненным топливозаборником which design guarantees possibility всасывания fuel in the pump from the lowermost point of a tank. Check up moving freedom топливозаборника
11. Examine a rubber sealing lining of an aperture лючка access to a fuel tank on presence of signs of damages. In case of need make replacement.

12. Clear surfaces ползуна and paths of a working element of the gauge of a mud touch and check up components on presence of cracks.



Installation is made upside-down. Pay attention to following moments:

a) Try not to bend at installation the lever of a float of the gauge;
b) At correct installation the float lever should appear is located perpendicularly axial line of the car;
c) Before installation grease an adjusting rubber lining with pure fuel;
d) Labels in the form of arrows on the top cover of assemblage and to aperture edge лючка in a tank should appear are combined;
e) Track correctness of an order of connection to assemblage of hoses of giving and fuel return (according to the marks put at dismantle).