Skoda Felicia

Since 1994 of release

Repair and car operation

Removal and installation of switches

Before to start performance of procedures disconnect a negative wire from the battery (the remark resulted in Section the General information and safety measures) see.

The switch of ignition/lock of blocking of a steering column

The Suspension bracket and steering see the Head.

Combined подрулевые switches

The general information

Combined подрулевой the switch consists of two separate knots fixed on a steering column of the car.

From switch assemblage it is deduced burn down the electroconductings, coming to an end with a 8-contact socket.

The switch of indexes of turns is equipped by the mechanical returnable device providing automatic switching-off of the alarm system after returning of a steering wheel in rectilinear position. From the switch it is deduced burn down the electroconductings, coming to an end with a 9-contact socket.

REMOVAL AND INSTALLATION

PERFORMANCE ORDER

1. Remove a steering wheel (the Suspension bracket and a steering see the Head).
2. On models without a driver's pillow of safety turn out the fixing screw and lower the bottom casing of a column, liberating it from clamps. Remove a casing from a column.
3. On all models turn out the fixing screw, release clamps and remove assemblage of the top casing from the panel of devices/holders of switches.

4. Now each of switches can be removed from the holder in an individual order after отпускания corresponding fixing clamps.

5. Having liberated the switch of their holder, disconnect from it electroconducting.

6. Installation is made upside-down. Track reliability подстыковки an electric socket and correctness of an arrangement of contacts of a horn. Having made sure that everything is all right, establish into place casings.

Press switches of the panel of devices

PERFORMANCE ORDER

1. Remove an instrument guard (see Has undressed Removal and installation of an instrument guard).

2. Assemblage of each of switches can be taken from a guard casing in an individual order by отпускания corresponding clamps.

3. At installation track reliability защелкивания switch clamps. The description of procedure of installation of an instrument guard is resulted in Section Removal and installation of an instrument guard.

The switch of management of functioning of the electric drive of external rear-view mirrors

PERFORMANCE ORDER

1. Lift the internal handle of a door, then accurately hook and remove the panel of its furnish.
2. Liberate the switch from clamps in assemblage of the handle and disconnect from it electroconducting.
3. Installation is made upside-down.

Assemblage of switches of management by functioning by steklopodemnikov/heating of forward seats

PERFORMANCE ORDER

1. Trying not to damage a console overlay, hook assemblage of switches by a small screw-driver and take it from the landing nest.
2. Disconnect electroconducting and take assemblage from the car.
3. Installation is made upside-down.

Door switches of illumination of salon

PERFORMANCE ORDER

1. Open a door and remove from switch assemblage a rubber protective cover.

2. Release clamps and, accurately having hooked, take the switch from a door pillar. Disconnect electroconducting (see an accompanying illustration). Glue a sticking out piece of electroconducting with the tip of a socket an adhesive tape that it casually has not failed in a rack.

If insufficiency of a weak point of electroconducting does not allow to make switch removal, remove from a rack of the panel of internal furnish, having provided with that access to a socket in last.

3. Installation is made upside-down. Track reliability of landing of a rubber protective cover.

The switch of illumination of a luggage space

PERFORMANCE ORDER

1. Remove assemblage of the lock of a door of a back (the Body and salon furnish see the Head).
2. Disunite an electric socket and take from замковой assemblages the switch of illumination of salon /

3. Installation is made upside-down. Before to establish on a door изоляционную a film and the panel of internal furnish make sure of serviceability of functioning of the switch.

The gauge-switch of stoplights

The Brake system see the Head.

The gauge-switch of the lever of a lay brake

PERFORMANCE ORDER

1. On in appropriate way the equipped models remove the central console (the Body and salon furnish see the Head).
2. On models without the central console hook and remove from the lever of a lay brake a decorative cover.

3. Turn out the fixing screw and remove a decorative cover of the gauge-switch.

4. Take the gauge-switch from the landing nest and disconnect from it electroconducting.

5. Installation is made upside-down. Before to establish into place the central console/cover of the lever, check up serviceability of functioning of the gauge-switch.

The switch of a choice of high-speed modes of the fan of a heater

PERFORMANCE ORDER

1. Remove assemblage of a casing of a heater/fan (see the Head of System of cooling, heating).

2. Disconnect electroconducting from switch assemblage.

3. Remembering adjusting position of all components (tips of cables are marked by a colour code), by means of nippers release clamps and disconnect приводные cables from the basis of the electromotor of the fan and the panel of switches of management of heater functioning.

4. Liberate a reflector of lamps of illumination from a forward part of the panel of switches of management.
5. Release clamps and remove assemblage of the switch of a choice of high-speed modes of the fan from the panel.

6. Installation is made upside-down. The description of procedure of installation of assemblage of a casing of a heater/fan is resulted in the Head of System of cooling, heating.