Skoda Felicia

Since 1994 of release

Repair and car operation

Removal and installation of assemblages of external lighting and alarm devices

Before to start to work do not forget to disconnect a negative wire from the battery (the prevention resulted in Section the General information and safety measures) see.

Head headlights

PERFORMANCE ORDER

1. Remove both lobbies of the index of turn.
2. On models of release till 1998 turn out the left and right bolts of fastening of the panel передка (access to bolts opens through apertures under installation of indexes of turns). Also turn out two screws of fastening of the top part of the panel to a cross-section beam of the lock of a cowl. Give fixing nuts in a back part of the panel, then remove last from the car.

3. On models of release since 1998 turn out the fixing screw, then remove the decorative cover established between a head block headlight and a forward bumper.

4. On all models turn out the top and bottom screws of fastening of a head block headlight.

5. Take a block headlight from the nest and disconnect electroconducting.

6. Having turned assemblage of a regulator of a direction of an optical axis, disconnect it from a back part of a block headlight, then definitively remove a headlight.

7. In case of need accurately release fixing clamps and remove from a block headlight a lens. Remove from a block headlight a sealant, check up its condition, in case of need replace.

8. Installation is made upside-down. All fixture should be tightened with demanded effort. Track reliability защелкивания clamps and regulator connection. In summary it is necessary to check up installation of an optical axis of a headlight (the Section Adjustment of a direction of an optical axis of head headlights - the general information and replacement of the mechanism of a regulator see).

Assemblages of forward indexes of turns

PERFORMANCE ORDER

1. Find a clamp of fastening of assemblage of the index in a forward corner of an impellent compartment of the car. Wring out a lock uvula and liberate assemblage of the index from a car wing.

2. Turn and take a cartridge with the lamp of the index established in it. In case of need for simplification of access to the index remove from the support an air cleaner casing (the Power supply system see a corresponding Part of the Head).

3. Installation is made upside-down. Track reliability защелкивания an assemblage clamp.

Forward antifog headlights

PERFORMANCE ORDER

The information resulted more low concerns only models of release till 1998 fresher data at the moment of drawing up of the present Management were absent.

1. Having hooked a small screw-driver with a flat sting, accurately remove facing of an antifog headlight from a forward bumper of the car.
2. Turn out fixing screws and take a headlight from the landing nest in a car bumper. Disconnect electroconducting and remove a headlight from the car.
3. Installation is made upside-down. In case of need rotation of the adjusting screw correct position of an optical axis of a headlight.

Lateral repeaters of forward indexes of turns

PERFORMANCE ORDER

1. Through a wheel arch push out assemblage of the repeater from a car wing.

2. Liberate a cartridge and remove a lens.

3. Installation is made upside-down. Track reliability of fixing of a lens of the repeater.

Assemblages of the back combined lanterns

PERFORMANCE ORDER

1. Release clamps and remove assemblage ламподержателя from a back part of a lantern.

2. Give fixing nuts and remove assemblage of a lantern from the car (together with a sealant) (see an accompanying illustration). Check up a sealant condition, in case of need make replacement.

3. Installation is made upside-down. Track correctness of landing of a sealant.

Top level Stoplight

PERFORMANCE ORDER

1. Turn out fixing screws and separate assemblage of a stoplight from an internal wall of a door of a back.

2. Disconnect electroconducting and remove assemblage from the car.

3. Installation is made upside-down.

Lantern of illumination of back licence plate

PERFORMANCE ORDER

1. Accurately having hooked a small screw-driver with a flat sting, liberate assemblage from a back door.
2. Take a cartridge and remove a lens.
3. Installation is made upside-down. Track reliability of fixing of a lens.