Skoda Felicia

1. Track reliability of fastening of an electric socket. At landing of assemblage to a regular place try not to admit зажимания wires.
2. Screw fixing screws and tighten them with demanded effort.
3. Make sure that in the car anybody is not present, then connect the battery. Through an open driver's door include ignition and make sure of serviceability of operation of a control lamp.

1. Accurately release clamps and uncover access to assemblage to a pillow the passenger party of the panel of devices.
2. Give nuts of fastening of assemblage of a pillow of safety and remove washers. Accurately remove assemblage from the seat and disconnect from it electroconducting.
3. For removal of a basic arm of assemblage turn out screws of fastening of an arm of the panel of furnish (through an aperture of the panel of a cover), then liberate the basis of the panel from clamps and remove section from the panel of devices. Give fixing nuts, throw off washers and remove a basic arm from a partition of an impellent compartment.

1. If removed, establish into place a basic arm on a partition of an impellent compartment and tighten nuts of its fastening with demanded effort. Latch into place the panel of furnish and strongly tighten screws of its fastening.
2. Connect electroconducting, having tracked reliability of fixing of a socket and plant pillow assemblage on the regular place, - try not to clamp a wire. Screw fixing nuts and tighten them with demanded effort. Establish on the panel of devices an access cover to assemblage of a pillow of safety.
3. Make sure that in the car anybody is not present, then connect the battery. Through an open driver's door include ignition and make sure of serviceability of operation of a control lamp.

1. Remove the central console (see Has undressed Removal and installation of the central console).
2. Remove a radio tape recorder (see Has undressed Removal and autoradio tape recorder installation), then unbend lock uvulas and take a sled of assemblage from the nest in the panel of devices. Disconnect from a sled the aerial of the roller bearing and food electroconducting.
3. Remove a sleeve connecting the basis of a casing of a heater with an air line of a back foot well.

4. Give fixing nuts and remove the foot emphasis established near to a pedal of coupling.

5. On models with a right-hand steering in a passenger foot well release a clamp and remove a decorative cover from the left arm of a support of pedal assemblage.

For отпускания a clamp take from it the central pin.

6. On all models unbend a carpet covering for the purpose of providing of access to located under the forward end of a foot air line of the block of management of a pillow of safety.

7. Give fixing nuts, throw off washers and remove the block of management from the support.

8. Release a clamp, disconnect electroconducting and take the block of management from the car.

1. Connect electroconducting and strongly latch a socket clamp. Establish the management block on the support (the arrow on is more true than a block plane should specify forward on the car). Screw fixing nuts and tighten them with demanded effort.
2. Establish into place an air sleeve, having tracked correctness of its introduction in gearing with reciprocal components.
3. Unbend a carpet covering and establish to the place of a foot emphasis, strongly having tightened its fixing nuts.
4. On models with a right-hand steering establish on the left arm of pedal assemblage a decorative cover and reliably fix its clamp.
5. On all models establish the central console (see Has undressed Removal and installation of the central console).
6. Connect to a sled of a radio tape recorder electroconducting and an antenna cable. Fill a sled in the panel of devices, having tracked reliability of fixing by its lock uvulas. Establish into place a radio tape recorder.
7. Make sure that in the car anybody is not present, then connect the battery. Through an open driver's door include ignition and make sure of serviceability of operation of a control lamp.

1. Remove assemblage of a driver's pillow of safety, then remove a steering wheel.

2. Mark position of the contact block in relation to a steering wheel, then turn out fixing screws and divide components. Do not rotate the contact block removed from the car!

1. Establish the contact block on a car steering wheel according to the landing labels put in the course of dismantle. Screw and strongly tighten fixing screws. At installation of the new block cut off and remove a fixing collar.
2. Establish into place a steering wheel (see Has undressed Removal and steering wheel installation), then establish assemblage of a driver's pillow of safety.

It is necessary to charge performance of procedures of removal and installation of assemblages of lateral pillows of safety to experts of car-care centre, in view of the big risk of damage of an upholstery of seats.