Skoda Felicia

Since 1994 of release

Repair and car operation



Shkoda Felitsija
+ Cars of mark Skoda Felicia
+ The maintenance instruction
+ Routine maintenance
+ Engine repair
+ Systems of cooling, heating
+ The power supply system
+ Engine electric equipment
+ Coupling
+ Transmission
+ Power shafts
+ Brake system
- Suspension bracket and steering
   The general information and safety measures
   Removal and installation ступичных assemblages of forward wheels
   Replacement of bearings of forward wheels
   Removal and installation of racks of a forward suspension bracket
   Major repairs of racks of a forward suspension bracket
   Removal, major repairs and installation of the bottom levers of a forward suspension bracket
   Replacement of spherical support of the bottom levers of a forward suspension bracket
   Removal and installation of the stabilizer of cross-section stability of a forward suspension bracket
   Removal and installation of racks of a bar of the stabilizer of cross-section stability of a forward suspension bracket
   Removal and installation of a forward stretcher
   Replacement of bearings of back naves
   Removal, major repairs and installation of racks of a back suspension bracket
   Major repairs of racks of a back suspension bracket
   Removal, major repairs and installation of pins of the back bridge
   Removal and installation of the back stabilizer of cross-section stability
   Removal and installation of the back bridge
   Removal and steering wheel installation
   Removal and installation of a steering column
   Major repairs of a steering column
   Removal and installation of assemblage of the lock of ignition/blocking of a wheel
   Removal, major repairs and installation of the steering mechanism
   Replacement of rubber protective covers картера the steering mechanism
   Removal of air stoppers from a hydraulic path of system of strengthening of a wheel
   Removal and installation of the helmsman наcоса
   Removal and installation of external tips of steering draughts
   Removal and installation of steering draught
   Corners of installation of wheels of the car - the general information
+ Body and salon furnish
+ Onboard electric equipment


c9b0dd5c

Removal and steering wheel installation

If the car is equipped by a driver's pillow of safety, on an overlay of a nave of a steering wheel the inscription “AIRBAG” will be put down.


The models which have been not equipped with a pillow of safety

REMOVAL

 PERFORMANCE ORDER

1. Establish forward wheels of the car in rectilinear position and block a steering column.
2. Accurately having hooked a small screw-driver with a flat sting, liberate the button of a horn from ступичной steering wheel parts. Disunite an electric socket and remove the button.
3. Give a nut of fastening of a steering wheel. Remove a washer.
4. Mark position of a wheel concerning a shaft of a steering column, then remove a wheel in equipped шлицами pins.

If the wheel is planted hardly and does not give in to removal, on it a palm, or pull to the right-to the left, simultaneously delaying upwards.

INSTALLATION

 PERFORMANCE ORDER

Installation is made upside-down. Pay attention to following moments:
a) Before installation expose the lever подрулевого the switch of indexes of turns in the central position, otherwise indexes will automatically not be disconnected on termination of turn;
b) Track correctness of combination of the landing labels put in the course of dismantle. A nut of fastening of a steering wheel tighten strictly with demanded effort.
The models equipped with a pillow of safety

Before steering wheel removal familiarise with preventions concerning observance of the safety measures, resulted in the Head the Onboard electric equipment of the present Management.

The models equipped with a pillow of safety

REMOVAL

 PERFORMANCE ORDER

1. Remove assemblage of a pillow of safety (the Onboard electric equipment see the Head).
2. Establish forward wheels of the car in rectilinear position, then block a steering column in this position, having taken out a key from the ignition lock.
3. Turn out the fixing screw in the top part of the bottom casing of a steering column. Lower a casing, liberate it from clamps and remove from the car.

4. Walk on electroconducting of the block of a pillow of safety to a socket. Disunite a socket that conducting could be removed together with a steering wheel.

5. Give a fixing nut, remove a washer and mark position of a steering wheel concerning a column shaft.

6. Remove a steering wheel with equipped шлицами shaft pins. Try not to damage electroconducting.

If the wheel is planted hardly and does not give in to removal, on it a palm, or pull to the right-to the left, simultaneously delaying upwards.

INSTALLATION

 PERFORMANCE ORDER

Installation is made upside-down. Pay attention to following moments:

a) Before installation expose the lever подрулевого the switch of indexes of turns in the central position, otherwise indexes will automatically not be disconnected on termination of turn;
b) Before steering wheel installation make sure that forward wheels of the car are in rectilinear position. Track correctness of combination of the landing labels put in the course of dismantle. A nut of fastening of a steering wheel tighten strictly with demanded effort;
c) Track correctness of a lining of electroconducting and reliability of connection of a socket of the block of a pillow of safety, only having made sure that everything is all right, start installation a casing of a steering column;
d) In summary establish into place assemblage of a pillow of safety (the Onboard electric equipment see the Head).