Skoda Felicia

Since 1994 of release

Repair and car operation



Shkoda Felitsija
+ Cars of mark Skoda Felicia
+ The maintenance instruction
+ Routine maintenance
+ Engine repair
+ Systems of cooling, heating
+ The power supply system
+ Engine electric equipment
+ Coupling
+ Transmission
+ Power shafts
+ Brake system
- Suspension bracket and steering
   The general information and safety measures
   Removal and installation ступичных assemblages of forward wheels
   Replacement of bearings of forward wheels
   Removal and installation of racks of a forward suspension bracket
   Major repairs of racks of a forward suspension bracket
   Removal, major repairs and installation of the bottom levers of a forward suspension bracket
   Replacement of spherical support of the bottom levers of a forward suspension bracket
   Removal and installation of the stabilizer of cross-section stability of a forward suspension bracket
   Removal and installation of racks of a bar of the stabilizer of cross-section stability of a forward suspension bracket
   Removal and installation of a forward stretcher
   Replacement of bearings of back naves
   Removal, major repairs and installation of racks of a back suspension bracket
   Major repairs of racks of a back suspension bracket
   Removal, major repairs and installation of pins of the back bridge
   Removal and installation of the back stabilizer of cross-section stability
   Removal and installation of the back bridge
   Removal and steering wheel installation
   Removal and installation of a steering column
   Major repairs of a steering column
   Removal and installation of assemblage of the lock of ignition/blocking of a wheel
   Removal, major repairs and installation of the steering mechanism
   Replacement of rubber protective covers картера the steering mechanism
   Removal of air stoppers from a hydraulic path of system of strengthening of a wheel
   Removal and installation of the helmsman наcоса
   Removal and installation of external tips of steering draughts
   Removal and installation of steering draught
   Corners of installation of wheels of the car - the general information
+ Body and salon furnish
+ Onboard electric equipment


c9b0dd5c

Removal and installation of steering draught

For a detachment of an internal tip of steering draught from реечного the mechanism the special key (Skoda № МР7-601) is required. The key is entered into reliable gearing with a tip casing that allows to release or tighten draught safely. Attempts of removal of draught without application of a special key are fraught with damage of components.

REMOVAL

 PERFORMANCE ORDER

1. Remove a tip of corresponding draught (see Has undressed Removal and installation of external tips of steering draughts).
2. Carefully clear of a dirt of a surface of draught and картера реечного a drive near to points of landing of a protective cover. Mark cover position on картере and a draught bar. Release bandage tapes and remove a cover both with картера the steering mechanism, and from draught.
3. By means of a special key liberate an internal tip of draught from steering рейки - keep рейку got on specially provided лыски рожковым a key. Try not to create in the course of a detachment of a tip excessive loading on the steering mechanism.
4. Remove assemblage the helmsman рейки. Check up the hinge of an internal tip of draught on presence of signs of an excessive weak point or a souring. Make sure that the draught bar not погнута and has no visible mechanical damages. A defective bar replace. Composers of the present Management recommend to make replacement of a protective cover of a tip without dependence from its condition.

INSTALLATION

 PERFORMANCE ORDER

1. Screw a tip in steering рейку and tighten it with demanded effort - in order to avoid overloads keep рейку for лыски рожковым a key.
2. Check up quality of stuffing of the hinge greasing, in case of need add necessary quantity of greasing of type Milykote Longterm 2/78, then accurately put on a protective cover a bar of draught and pull it on картер the steering mechanism.
3. Make sure that the cover is not overwound and level its external edges concerning the labels put in the course of dismantle. Fix a cover bandage tapes.
4. Establish into place an external tip of steering draught (see Has undressed Removal and installation of external tips of steering draughts).