Skoda Felicia

Since 1994 of release

Repair and car operation



Shkoda Felitsija
+ Cars of mark Skoda Felicia
+ The maintenance instruction
+ Routine maintenance
+ Engine repair
+ Systems of cooling, heating
+ The power supply system
+ Engine electric equipment
+ Coupling
+ Transmission
+ Power shafts
+ Brake system
- Suspension bracket and steering
   The general information and safety measures
   Removal and installation ступичных assemblages of forward wheels
   Replacement of bearings of forward wheels
   Removal and installation of racks of a forward suspension bracket
   Major repairs of racks of a forward suspension bracket
   Removal, major repairs and installation of the bottom levers of a forward suspension bracket
   Replacement of spherical support of the bottom levers of a forward suspension bracket
   Removal and installation of the stabilizer of cross-section stability of a forward suspension bracket
   Removal and installation of racks of a bar of the stabilizer of cross-section stability of a forward suspension bracket
   Removal and installation of a forward stretcher
   Replacement of bearings of back naves
   Removal, major repairs and installation of racks of a back suspension bracket
   Major repairs of racks of a back suspension bracket
   Removal, major repairs and installation of pins of the back bridge
   Removal and installation of the back stabilizer of cross-section stability
   Removal and installation of the back bridge
   Removal and steering wheel installation
   Removal and installation of a steering column
   Major repairs of a steering column
   Removal and installation of assemblage of the lock of ignition/blocking of a wheel
   Removal, major repairs and installation of the steering mechanism
   Replacement of rubber protective covers картера the steering mechanism
   Removal of air stoppers from a hydraulic path of system of strengthening of a wheel
   Removal and installation of the helmsman наcоса
   Removal and installation of external tips of steering draughts
   Removal and installation of steering draught
   Corners of installation of wheels of the car - the general information
+ Body and salon furnish
+ Onboard electric equipment


c9b0dd5c

Major repairs of racks of a forward suspension bracket

Components of a rack of a forward suspension bracket

1 — the Shock-absorber
2 — the Screw spring
3 — the Protective cover
4 — the Buffer of a course of compression
5 — the Top plate of a spring

6 — the Bearing
7 — the Rubber pillow
8 — the Top support of a rack
9 — the Rubber ring
10 — Nut М12


The special tool for сжимания screw springs of a suspension bracket is required. Composers of the present Management recommend to use the tool of adjustable type - ask in shops of automobile accessories. Any attempts of dismantling of racks without use of the special tool are fraught with reception of serious traumas.

At assemblage the new nut of a fixing plate is required.

 PERFORMANCE ORDER

1. Remove a rack from the car, clear it of a dirt, then clamp vertically in a vice with soft sponges. By means of the special adaptation compress a screw spring, completely having unloaded plates. Track correctness of fastening of the tool on spring coils (strictly adhere to instructions of manufacturers).

2. A wrench block a rod of the piston of rack-mount assemblage from проворачивания and give a nut of fastening of the top plate.

3. Remembering adjusting position of components, give a nut...

Also remove from a rack тарельчатую a washer...

And a fixing plate...

At assemblage the nut is subject to replacement without fail.

4. Remove the rubber plug...

... The holder of the bearing...

... The bearing...

... The remote plug and the top plate of a spring...

Then remove a screw spring...

5. Remove from piston assemblage of the shock-absorber a rubber protective cover and the buffer of a course of compression.

6. Attentively examine the shock-absorber on presence of traces of leaks of a hydraulic liquid. Check up the piston on presence of cavities, and the shock-absorber case on presence of mechanical damages. Keeping the shock-absorber vertically, check up serviceability of its functioning at first on all length of its course, then on short compression with a course from 50 to 100 mm. In both cases resistance to compression should be uniform and continuous. Otherwise the shock-absorber is faulty and is subject to replacement.
7. Check up all components on presence of signs of deterioration, deformations and mechanical damages, special attention giving to a condition of the bearing and the remote plug. Defective details replace.
8. Establish on the shock-absorber the buffer of a course of compression and a rubber protective cover. Track correctness of landing of a bottom edge of a cover on the shock-absorber case.
9. Establish into place a screw spring. Track correctness of landing of its bottom end face concerning a plate emphasis.

10. Completely stretch the shock-absorber, then establish on it the top plate, again correctly having developed its emphasis concerning a spring end face.

11. Establish the remote plug, the bearing, the holder of the bearing and the rubber plug, trace establish the top fixing plate.
12. Establish on the piston тарельчатую a washer, then screw a new nut. Keeping the piston from проворачивания, tighten a nut of a fixing plate with demanded effort.
13. Having made sure of correctness of landing of a spring on an emphasis of plates, release compressing tool and remove it from a rack.