Skoda Felicia

Since 1994 of release

Repair and car operation



Shkoda Felitsija
+ Cars of mark Skoda Felicia
+ The maintenance instruction
+ Routine maintenance
+ Engine repair
+ Systems of cooling, heating
+ The power supply system
+ Engine electric equipment
+ Coupling
+ Transmission
+ Power shafts
+ Brake system
- Suspension bracket and steering
   The general information and safety measures
   Removal and installation ступичных assemblages of forward wheels
   Replacement of bearings of forward wheels
   Removal and installation of racks of a forward suspension bracket
   Major repairs of racks of a forward suspension bracket
   Removal, major repairs and installation of the bottom levers of a forward suspension bracket
   Replacement of spherical support of the bottom levers of a forward suspension bracket
   Removal and installation of the stabilizer of cross-section stability of a forward suspension bracket
   Removal and installation of racks of a bar of the stabilizer of cross-section stability of a forward suspension bracket
   Removal and installation of a forward stretcher
   Replacement of bearings of back naves
   Removal, major repairs and installation of racks of a back suspension bracket
   Major repairs of racks of a back suspension bracket
   Removal, major repairs and installation of pins of the back bridge
   Removal and installation of the back stabilizer of cross-section stability
   Removal and installation of the back bridge
   Removal and steering wheel installation
   Removal and installation of a steering column
   Major repairs of a steering column
   Removal and installation of assemblage of the lock of ignition/blocking of a wheel
   Removal, major repairs and installation of the steering mechanism
   Replacement of rubber protective covers картера the steering mechanism
   Removal of air stoppers from a hydraulic path of system of strengthening of a wheel
   Removal and installation of the helmsman наcоса
   Removal and installation of external tips of steering draughts
   Removal and installation of steering draught
   Corners of installation of wheels of the car - the general information
+ Body and salon furnish
+ Onboard electric equipment


c9b0dd5c

Replacement of bearings of forward wheels

Assemblage of a nave of a forward wheel

1 — the Rotary fist
2 — the Bearing
3 — the Spring ring
4 — the Nave

5 — the Nut
6 — the Spherical support
7 — the Brake disk


Двухрядный the roller wheel bearing has tight execution. Stuffing of assemblage by greasing and pretightness installation are made on car manufacturer. The bearing is calculated on all service life of the car and does not require any additional service. Try not to suppose a tightening ступичной a nut with excessive effort, - use динамометрическим a key.


For performance of procedures of dismantling and assemblage of the wheel bearing the suitable press in which absence will fit big верстачные a vice with a set cylindrical оправок (as those perfectly is required face heads approaching on the size) will approach. Internal holders of the bearing внатяг are planted on a nave. If at dismantle of the bearing the holder remained on a nave, for its removal the special stripper with captures лезвийного type is required.

 PERFORMANCE ORDER

1. Remove ступичную assemblage from the car (see Has undressed Removal and installation ступичных assemblages of forward wheels).

2. Strongly lay assemblage on pair wooden blocks, or clamp it in a vice with soft sponges. By means of cylindrical оправки, leaning only in internal edge ступичного a flange, squeeze out last of the bearing. If the external part of an internal holder of the bearing remains on a nave, take advantage of a stripper.

3. Remove a lock ring from the external end ступичной assemblages.

4. Strongly prop up lateral aspect ступичной assemblages. By means of cylindrical оправки, leaning only in an internal holder of the bearing, squeeze out assemblage of last of a nave.

5. Carefully clear ступичную assemblage of a dirt and greasing traces. An emery paper remove agnails and the teases, capable to prevent assemblage of components. Check up components on presence of cracks and other signs of deterioration. Defective details replace.
6. For the purpose of simplification of assemblage of components slightly grease an external holder of the bearing and a pin of a flange of a nave with oil of type Optimol VP317.

7. Strongly prop up a nave and fill in it the bearing. By means of cylindrical оправки, resting only in an external holder of the bearing, запрессуйте last against the stop in a nest in a nave. Make sure of perpendicularity of landing of the bearing.

8. Having planted the bearing in a nave, fix its lock ring. Track correctness of landing of a ring in the flute.
9. Strongly prop up flange lateral aspect ступичной assemblages Put on the flange end an internal holder of the bearing. By means of cylindrical оправки, resting only in an internal holder, plant the bearing against the stop in an assemblage coat hanger. Check up freedom of rotation of a flange, remove surplus of oil/greasing.
10. Establish ступичную assemblage on the car (see Has undressed Removal and installation ступичных assemblages of forward wheels).