Skoda Felicia

1. Remove a decorative cap of a wheel disk/nave, then ослабьте a nut of a power shaft and bolts of fastening of a wheel.
2. Prop up wedges back wheels, cock a lay brake, then поддомкратьте redock of the car and establish it on props. Remove a corresponding forward wheel.
3. On the models equipped ABS, отболтите the wheel gauge and, without disconnecting electroconducting, take him aside from ступичной assemblages (Removal and installation of racks of a bar of the stabilizer of cross-section stability of a forward suspension bracket see the Head).

4. Give ступичную a nut and remove washers. If have forgotten to weaken a nut while the car stood on the earth, screw in a nave pair (at least) bolts of fastening of a wheel and strongly them tighten, then ask the assistant to squeeze out firmly a pedal of a foot brake for the purpose of blocking of a nave from проворачивания and give a nut. At assemblage ступичная the nut is subject to replacement without fail.

5. Take шплинт and give a nut of fastening of a tip of steering draught on the rotary lever ступичной assemblages. By means of a stripper of spherical support liberate a tip from the lever.

6. If be going to dismantle ступичные bearings, remove a brake disk, otherwise screw two bolts of fastening to a nave of assemblage of a support with анкерной скобой and remove assemblage from a brake disk. Tie up a support a wire to a suspension bracket spring, - try not to admit an excessive tension of a flexible brake hose.

7. On equipped with the stabilizer of cross-section stability models give a nut of fastening of a rack of a bar of the stabilizer to the bottom lever of a suspension bracket, remove a washer and take a rubber insert.

8. On all models give a nut and take a coupling bolt of a spherical support of the bottom lever of a suspension bracket from the basis ступичной assemblages. By means of mount cautiously lower the bottom lever, liberating a spherical support from the landing collar in ступичной to assemblage. On the models equipped with the stabilizer of cross-section stability, try not to admit loss of a rubber pillow and a washer of the top support of a rack of a bar of the stabilizer. The coupling bolt of a spherical support is subject to replacement without fail (in the complete set with the nut).

9. Give a nut and take a coupling bolt of fastening ступичной assemblages to a suspension bracket rack. The nut of a coupling bolt is subject to replacement without fail.

10. Separate ступичную assemblage from a suspension bracket rack, then remove it with equipped шлицами pins of an external SHRUS of a power shaft and take from under the car. If assemblage does not separate from a rack, with the big screw-driver with a flat sting accurately dissolve sponges of a fixing collar. At too hard landing of a rack to a shaft pin bring down its hammer with soft the brisk.

1. Carefully clear landing шлицы naves and pins of an external SHRUS of a power shaft. Against the stop plant ступичную assemblage on a shaft pin, establish a washer, then screw new ступичную a nut. Slightly tighten a nut.
2. Plant ступичную assemblage on a suspension bracket rack, having got an ear of last in a collar groove. Achieve combination of apertures, then insert a coupling bolt, screw a new nut and tighten it with demanded effort.
3. Achieve correct placing of a shaft of a spherical support of the bottom lever with a collar ступичной assemblage, insert a coupling bolt, screw a new nut and tighten it with demanded effort. On the models equipped with the stabilizer of cross-section stability place a rack of a bar of the stabilizer on the bottom lever of a suspension bracket, having tracked correctness of an arrangement of a rubber insert and a washer of the top support.
4. Where it is required establish on a stabilizer bar a rubber insert and a washer of the bottom support, screw fixing to a hook and tighten it with demanded effort.
5. In the correct image get a shaft of the spherical hinge of a tip of steering draught in a landing nest in ступичной assemblages and strongly tighten its fixing nut. Fix a nut new шплинтом.
6. Where it is required establish on a nave a brake disk (the Brake system see the Head). Plant into place assemblage of a support with анкерной скобой, - track correctness of landing from both parties of a disk brake колодок. Tighten with demanded effort fastening bolts анкерной скобы (the Brake system see the Head).
7. On models with ABS establish into place the wheel gauge (the Brake system see the Head).
8. Establish into place a wheel, then lower the car on the earth and tighten nuts of fastening of a wheel with demanded effort.
9. Definitively tighten with demanded effort ступичную a nut, then establish into place a decorative cap of a disk/nave.