Skoda Felicia

Since 1994 of release

Repair and car operation



Shkoda Felitsija
+ Cars of mark Skoda Felicia
+ The maintenance instruction
+ Routine maintenance
+ Engine repair
+ Systems of cooling, heating
+ The power supply system
+ Engine electric equipment
+ Coupling
+ Transmission
+ Power shafts
+ Brake system
- Suspension bracket and steering
   The general information and safety measures
   Removal and installation ступичных assemblages of forward wheels
   Replacement of bearings of forward wheels
   Removal and installation of racks of a forward suspension bracket
   Major repairs of racks of a forward suspension bracket
   Removal, major repairs and installation of the bottom levers of a forward suspension bracket
   Replacement of spherical support of the bottom levers of a forward suspension bracket
   Removal and installation of the stabilizer of cross-section stability of a forward suspension bracket
   Removal and installation of racks of a bar of the stabilizer of cross-section stability of a forward suspension bracket
   Removal and installation of a forward stretcher
   Replacement of bearings of back naves
   Removal, major repairs and installation of racks of a back suspension bracket
   Major repairs of racks of a back suspension bracket
   Removal, major repairs and installation of pins of the back bridge
   Removal and installation of the back stabilizer of cross-section stability
   Removal and installation of the back bridge
   Removal and steering wheel installation
   Removal and installation of a steering column
   Major repairs of a steering column
   Removal and installation of assemblage of the lock of ignition/blocking of a wheel
   Removal, major repairs and installation of the steering mechanism
   Replacement of rubber protective covers картера the steering mechanism
   Removal of air stoppers from a hydraulic path of system of strengthening of a wheel
   Removal and installation of the helmsman наcоса
   Removal and installation of external tips of steering draughts
   Removal and installation of steering draught
   Corners of installation of wheels of the car - the general information
+ Body and salon furnish
+ Onboard electric equipment


c9b0dd5c

Removal and installation of external tips of steering draughts

For performance of the given procedure the stripper of spherical support is required.

REMOVAL

 PERFORMANCE ORDER

1. Cock a lay brake, then поддомкратьте redock of the car and establish it on props. Remove a corresponding forward wheel.
2. If the tip does not require replacement and will be used further, take advantage of a measuring instrument of planeness and чертилкой mark its position on draught.
3. Having fixed a draught bar, on a turn quarter ослабьте a counternut of fastening of a tip. Leave a nut in this position in quality of a reference point at assemblage.

4. Take шплинт and give a nut of fastening of an external tip of draught. Liberate the hinge of a tip from the rotary lever ступичной assemblages - in case of need take advantage of a stripper.

5. Screw together a tip from a bar of steering draught - count quantity of turns and try not to shift a counternut.
6. In case of need count quantity of coils of a carving from an end face of a bar to a counternut. Result write down. Now the nut can be removed also.
7. Carefully clear a tip and a carving part of draught. If the hinge is stirred up or, on the contrary, has soured, it is necessary to replace a tip. Carefully check up a condition конусного a shaft and a carving part of a spherical finger. In case of need in an individual order replace the damaged cover of the spherical hinge. Make sure that the hinge is filled by greasing. In case of need add necessary quantity of greasing of type Milykote Longterm 2/78, then establish a new cover and fix its bandages.

INSTALLATION

 PERFORMANCE ORDER

1. If it is required, screw on a bar of draught a counternut (in former position - be verified by quantity of coils of a carving).
2. Screw a tip on a draught bar on former quantity of turns (thus the counternut should appear it is separated from a tip end face exactly on a turn quarter - achieve combination of the labels put in the course of dismantle).
3. Fill the hinge of a tip of draught in the rotary lever ступичной assemblages and screw a fixing nut. Strongly tighten a nut and fix its new шплинтом.
4. Establish into place a wheel, then lower the car on the earth and tighten wheel bolts with demanded effort.
5. Check up corners of installation of forward wheels, in case of need make corresponding updating (see Has undressed Corners of installation of wheels of the car - the general information). Now tighten a counternut of a tip of steering draught with demanded effort.