Skoda Felicia

1. Prop up wedges forward wheels, then поддомкратьте a back of the car and establish it on props. Disconnect a negative wire from the battery and remove both back wheels.

2. Operating according to the instructions resulted in the Head Brake system, execute following procedures: a) Give контрящие and adjusting nuts of cables of a drive of a lay brake and disconnect the last from an equalizer plate. Under the car liberate the forward ends of both cables from intermediate clamps on the car bottom that they could be freely removed together with the back bridge; b) Walk on hydraulic tubes from boards of brake mechanisms to штуцерных the connections fixed in arms on the bottom of the car directly ahead of assemblage of the back bridge. Carefully wipe connections, then give накидные nuts and disconnect tubes. Release fixing collars and liberate hoses from arms. At once закупорьте the open ends tenches for the purpose of minimisation of losses of a brake liquid, and also in order to avoid hit in hydraulic system of a dirt; c) On equipped ABS models walk on electroconducting from wheel gauges to sockets. Disunite both sockets. Liberate electroconducting from intermediate clamps that it could be free removed together with the bridge; d) On models without ABS, equipped sensitive to degree of loading of the car the valve-regulator, mark head position болтав клапанной springs in relation to the bridge. Give a nut, take a bolt and disconnect a spring.

3. Make sure that all are disconnected disturbing to performance of works components, then prop up assemblage of the back bridge тележечным a jack.
4. Give nuts of bolts of fastening to the bridge of the bottom support of racks of a suspension bracket.

At nut assemblage are subject to replacement without fail.

5. By means of the assistant give nuts of axial bolts of the bridge and accurately take last from under the car.

Nuts of axial bolts of the bridge are subject to replacement without fail.

6. Check up a condition of axial plugs of the bridge. In case of need make replacement. Replacement of axial plugs is made with application of a hydraulic press and it is necessary to charge its performance to experts of car-care centre. At presence near at hand the necessary equipment squeeze out plugs and запрессуйте on their place new, having taken advantage оправкой, the plug resting against external edge.
7. In need of replacement assembly скоб the bridge mark their position on the car bottom, then give fixing bolts and remove arms. Establish to the place of the removed arms new, screw fixing bolts, level скобы according to the labels put in the course of dismantle, then tighten fixture with demanded effort.

If replacement assembly скоб was made, after assemblage end it is necessary to check up parallelism of installation of the bridge (see Has undressed Corners of installation of wheels of the car - the general information).

1. Get the bridge on the regular place and insert axial bolts. Screw new nuts and tighten them, while slightly.
2. Insert bolts of the bottom support of fastening to the bridge of racks of a suspension bracket. Screw new nuts, also without tightening them at the given stage.
3. According to the instructions resulted in the Head Brake system, execute following procedures:

a) At a corresponding complete set connect to the bridge a working spring sensitive to degree of loading of the car of the valve-regulator. Track correctness of installation of washers. Having achieved combination of the labels put in the course of dismantle, tighten a fixing nut with demanded effort;
b) On equipped ABS models connect electroconducting to wheel to gauges. Track correctness of a lining of wires and reliability of their fastening in intermediate clamps;
c) Collars fix in the arms brake hoses. Connect tubes and strongly tighten накидные nuts штуцерных connections;
d) Make sure of correctness of a lining of both cables of a drive of a lay brake. Connect cables to the lever. Screw adjusting nuts and fix them контрящими. Yet do not establish into place a lever cover / the central console.

4. Establish into place back wheels, lower the car on the earth and tighten wheel bolts with demanded effort.
5. Shake the car standing on wheels for усадки components, then tighten with demanded effort of a nut of axial bolts of the bridge and fastening support to it of suspension bracket racks.
6. Entirely pump over brake system (the Brake system see the Head), on in appropriate way the equipped models испрвности functioning of the valve-regulator of pressure it is necessary to charge check by the expert of car-care centre.