Skoda Felicia

Since 1994 of release

Repair and car operation



Shkoda Felitsija
+ Cars of mark Skoda Felicia
+ The maintenance instruction
+ Routine maintenance
+ Engine repair
+ Systems of cooling, heating
+ The power supply system
+ Engine electric equipment
+ Coupling
+ Transmission
+ Power shafts
+ Brake system
- Suspension bracket and steering
   The general information and safety measures
   Removal and installation ступичных assemblages of forward wheels
   Replacement of bearings of forward wheels
   Removal and installation of racks of a forward suspension bracket
   Major repairs of racks of a forward suspension bracket
   Removal, major repairs and installation of the bottom levers of a forward suspension bracket
   Replacement of spherical support of the bottom levers of a forward suspension bracket
   Removal and installation of the stabilizer of cross-section stability of a forward suspension bracket
   Removal and installation of racks of a bar of the stabilizer of cross-section stability of a forward suspension bracket
   Removal and installation of a forward stretcher
   Replacement of bearings of back naves
   Removal, major repairs and installation of racks of a back suspension bracket
   Major repairs of racks of a back suspension bracket
   Removal, major repairs and installation of pins of the back bridge
   Removal and installation of the back stabilizer of cross-section stability
   Removal and installation of the back bridge
   Removal and steering wheel installation
   Removal and installation of a steering column
   Major repairs of a steering column
   Removal and installation of assemblage of the lock of ignition/blocking of a wheel
   Removal, major repairs and installation of the steering mechanism
   Replacement of rubber protective covers картера the steering mechanism
   Removal of air stoppers from a hydraulic path of system of strengthening of a wheel
   Removal and installation of the helmsman наcоса
   Removal and installation of external tips of steering draughts
   Removal and installation of steering draught
   Corners of installation of wheels of the car - the general information
+ Body and salon furnish
+ Onboard electric equipment


c9b0dd5c

Removal, major repairs and installation of the bottom levers of a forward suspension bracket

Forward suspension bracket

1 — the Cross-section beam
2 — the Bolt (25 Nanometers)
3 — Skoba
4 — the Rubber plug
5 — a bolt
6 — the Holder with резинометаллической the plug
7 — Samokontrjashchajasja a nut (100 Nanometers)
8 — the Back pillow of the cross-section lever
9 — Bolt М6 (7 Nanometers)
10 — the Bolt (70 Nanometers)
11 — the Washer
12 — the Cross-section lever of a suspension bracket

13 — Bolts
14 — the Spherical support
15 — the Nut (25 Nanometers)
16 — the Forward pillow of the cross-section lever
17 — Samokontrjashchajasja a nut (90 Nanometers)
18 — the Bolt
19 — the Bolt
20 — the Arm of fastening of a jet bar with a rubber pillow
21 — the Washer
22 — Samokontrjashchajasja a nut (5 Nanometers)
23 — the Bolt (45 Nanometers)
24 — the Washer


At assemblage the new nut of a coupling bolt of a tent support and also a new nut of a forward axial bolt is required. Also prepare new spring washers of bolts of fastening of the lever.

REMOVAL

 PERFORMANCE ORDER

1. Prop up wedges back wheels, cock a lay brake, then поддомкратьте redock of the car and establish it on props. Remove a corresponding forward wheel.
2. On the models equipped with the stabilizer of cross-section stability, give a nut of fastening of a rack of a bar of the stabilizer to the bottom lever, remove a washer and the bottom rubber insert. Components of fastening of the bottom lever of a suspension bracket are presented on an illustration.

3. On all models give a nut and take a coupling bolt of a collar of fastening ступичной assemblages to the bottom lever...

... By means of mount cautiously lower the bottom lever, liberating a spherical support from the landing collar in the basis ступичной assemblages. On the models equipped with the stabilizer of cross-section stability, try not to admit loss of a rubber pillow and a washer of the top support of a rack of a bar of the stabilizer.

The nut of a coupling bolt of a spherical support is subject to replacement without fail.

4. Give a nut of a forward axial bolt of the bottom lever, remove a washer.

At assemblage the nut is subject to replacement without fail.

5. Give a nut and bolts of fastening of the back axial plug of the bottom lever to the car bottom...

... Remove from bolts spring washers - at assemblage they are subject to replacement without fail.

On some models the nut of fastening of the plug can be replaced by a rivet.

6. Take out master a bolt from the plug of a forward support and take assemblage of the lever from under the car.


Major repairs


 PERFORMANCE ORDER

1. Carefully wipe the lever and landing surfaces of its support, having removed with all of them traces of a dirt and an anticorrosive covering of the bottom. Attentively examine assemblage on presence of cracks, deformations and other mechanical damages. Special attention give to a condition of axial plugs. Defective components replace.
2. For replacement of axial plugs the hydraulic press, a stripper of bearings and some remote plugs is required. In view of told, performance of the given work will charge more correctly to the experts of car-care centre having all necessary equipment. The order of carrying out of procedure is described more low.
3. For replacement of the forward plug first of all try to remember its correct adjusting position. Then reliably prop up the lever and squeeze out of it the plug. Carefully wipe nest walls under plug landing. Before installation of the new plug moisten with its soap solution.

4. The back plug also should be established strictly definitely an obligatory order to the relation to the lever. Otherwise while in service the car the plug will be exposed to excessive loadings. Squeeze out assemblage of the lever of an arm, then squeeze out the plug of the lever end. Carefully wipe nest walls under plug landing. Before installation of the new plug moisten with its soap solution. At assemblage track, that the plug has appeared in the correct image is developed by the groove concerning the lever.

INSTALLATION

 PERFORMANCE ORDER

1. Get the bottom lever of a suspension bracket on the regular place and fill a shaft of a spherical support in a collar in the basis ступичной assemblages. On equipped the stabilizer of cross-section stability models arrange a rack of a bar of the stabilizer on the lever, having tracked correctness of landing of a rubber insert and a washer of the top support.
2. Insert a forward axial bolt, establish a washer, screw a new nut and tighten it, while only by hand.
3. Screw a fixing nut (at a corresponding complete set) an arm of the back axial plug. Screw bolts (do not forget to replace spring washers). Tighten bolts with demanded effort, then tighten a nut. At a corresponding complete set instead of a nut establish a new rivet.
4. Make sure of correctness of landing of a coupling bolt in ступичной to assemblage. Screw a new nut and tighten it with demanded effort.
5. Where it is required, establish a rubber insert and a washer of the bottom support of a rack of a bar of the stabilizer, screw a nut and tighten it with demanded effort.
6. Establish into place a wheel, then lower the car on the earth and with demanded effort tighten wheel bolts.
7. Shake the car for усадки lever components, then tighten with demanded effort a nut of a forward axial bolt.