Skoda Felicia

1. Having waited full cooling of the engine, firmly cock a lay brake, then поддомкратьте redock of the car and establish it on props.

2. Uncover a jellied mouth of a broad tank (having turned a cover counter-clockwise to the first emphasis, dump residual pressure in system, then uncover definitively). Establish reception container under the drain stopper screwed in the basis passing under pulley of a cranked shaft of a metal tube.

3. Turn out a drain stopper and lower cooling liquid in the prepared capacity.

4. When вытекание liquids will stop, move capacity under a drain stopper in a forward part of the left end face of the block of cylinders, it is direct under the gauge-switch of pressure of oil. Turn out a stopper and merge in capacity the rests of a cooling liquid.

5. If опорожнение systems it is made not for the purpose of replacement of a cooling liquid, check up a condition of last. Make sure that the merged liquid has fulfilled no more than three years. If everything is all right, the liquid can be used repeatedly though composers of the present Management and do not recommend to adhere to similar practice. Prepare replaceable sealing washers of drain stoppers.
6. Clean a carving of stoppers and put on them new sealing washers. Slightly grease stoppers with fresh hermetic, then screw them on the regular places and tighten with demanded effort.

1. Having waited full cooling of the engine, uncover a jellied mouth of a broad tank. Establish suitable drain capacity under the union of the bottom hose of a radiator.
2. Release a fixing collar, disconnect the bottom hose from a radiator and merge cooling liquid in the prepared capacity.
3. If опорожнение systems it is made not for the purpose of replacement of a cooling liquid, check up a condition of last. Make sure that the merged liquid has fulfilled no more than two years. If everything is all right, the liquid can be used repeatedly though composers of the present Management and do not recommend to adhere to similar practice.
4. When вытекание liquids will stop, connect a hose into place and fix its collar.

1. At the negligent relation to performance of regular change of a cooling liquid, and also in case of strong разжижения antifreeze as a result of frequent addition in system of simple water, there is a gradual decrease in efficiency of cooling of the engine owing to adjournment on walls of channels and galleries of system of a scum and corrosion products. Restoration of initial productivity of system of cooling can be made by its washing.
2. Radiator washing is made separately from охладительного a path of the engine in order to avoid risk of pollution of all system.

1. Disconnect from a radiator the top and bottom hoses of the big section, and also all other systems of cooling concerning functioning hoses (see the Head of System of cooling, heating).
2. Insert into a reception branch pipe of the top hose on a radiator a garden hose and include water delivery. Continue washing until the water following through the bottom branch pipe, will not get an absolute transparency.
3. If to achieve a transparency of a target stream it is not possible, it is necessary to use for radiator washing of one set let out now патентованных cleaners. In cases of especially serious pollution the radiator should be removed from the car and to subject обратнопоточной to washing.

1. Remove the thermostat (see the Head of System of cooling, heating), then temporarily establish to the place of its cover.
2. Having disconnected from a radiator the top and bottom hoses, pass in the first end of a garden hose and submit water. Continue washing until the stream following through the bottom hose does not become absolutely pure and transparent.
3. Having finished washing, establish into place the thermostat and restore initial connection of hoses of system of cooling (see the Head of System of cooling, heating).

Before to start refuelling of system of cooling, make sure of serviceability of a condition and reliability of fastening on the unions and branch pipes of all hoses concerning its functioning. Do not forget that the system at any time year should refuel demanded structure a mix of antifreeze with water. Fast development of corrosion of internal walls of channels of a path otherwise will begin.

1. Make sure of reliability of a tightening of both drain stoppers.

2. Lower the car on the earth and turn out the gauge of temperature of a cooling liquid (CTS) from the top part of a casing of the thermostat (see the Head of System of cooling, heating).

3. Uncover a jellied mouth of a broad tank and slowly start to fill in in a tank a mix of demanded structure (see more low), observing of a thermostat casing. When through an aperture under installation CTS the free mix from air bubbles will start to follow, screw the gauge into place.
4. Having established to the place of CTS, continue to fill in a mix until its level in a broad tank will not rise to a mark the MOVE on a translucent wall of the last.
5. Establish into place a cover of a jellied mouth, and strongly tighten it.
6. Start the engine and warm up it to normal working temperature (should join and again be switched off the fan of system of cooling).
7. Muffle the engine, allow to it to cool down, then once again check up level of a cooling liquid in a broad tank. In case of need make updating.

1. Make sure of serviceability of a condition and reliability of fastening on the union of the bottom hose of a radiator. Uncover a jellied mouth of a broad tank.
2. Uncover a jellied mouth of a broad tank and slowly fill in in a mouth a mix of demanded structure until its level in a broad tank will not rise to a mark the MOVE on a translucent wall of the last.
3. Establish into place a cover of a jellied mouth, and strongly tighten it.
4. Start the engine and warm up it to normal working temperature (should join and again be switched off the fan of system of cooling).
5. Muffle the engine, allow to it to cool down, then once again check up level of a cooling liquid in a broad tank. In case of need make updating.

1. Replacement of a cooling liquid should be made according to the schedule of routine maintenance of the car (see above). Only the regularity of change of antifreeze allows to minimise corrosion охладительного a path and to provide demanded frost resistance of a mix in a winter season.
2. Use for mix configuration only antifreeze on base этиленгликоля, in the best way approaching for refuelling of automobile systems of the cooling which path consists of diverse metals. Requirements to mix structure, depending on necessary level of protection, are resulted in Specifications.
3. Before the beginning of refuelling the system should be completely emptied, washed preferably out, and the condition and reliability of fastening of all hoses охладительного a path are checked carefully up.
4. Having finished system refuelling, attach to a mouth of a broad tank a label with the data about date of refuelling and structure of the filled in mix. At all subsequent updatings of level in system the mix of the same structure that is specified on an information label should be added only.
5. At all do not use intended for application in system of cooling antifreeze in quality морозоупорной an additive to a liquid of washing of glasses - such practice will inevitably lead to damage of a paint and varnish covering кузовных panels.