|
|
Skoda FeliciaSince 1994 of releaseRepair and car operation |
|
|
Shkoda Felitsija + Cars of mark Skoda Felicia + The maintenance instruction + Routine maintenance - Engine repair - Repair without extraction from the car of the petrol engine of 1.3 l The description of the basic knots and mechanisms Check of a condition of shatunno-piston group on hearing and measurement компрессионного pressure in cylinders Reduction of the piston of the first cylinder in position of the top dead point (ВМТ) Removal and installation of a cover of a casing of a camshaft Removal, check of a condition and installation of assemblage of an axis коромысел Removal and installation of a head of cylinders in gathering with the inlet pipeline and a final collector Removal, check of a condition and installation of a forward cover, chain and asterisks of drive ГРМ Removal, check of a condition and installation of components of the oil pump Removal and pallet installation картера the engine Replacement of epiploons of a cranked shaft Removal, check of a condition and flywheel installation Check of a condition and replacement of rubber pillows of support of a suspension bracket of the power unit Removal, installation and adjustment of effort of a tension of a belt of a drive of auxiliary units + Repair without extraction from the car of the petrol engine of 1.6 l + Repair without extraction from the car of the diesel engine + Dismantle of the power unit and engine major repairs + Systems of cooling, heating + The power supply system + Engine electric equipment + Coupling + Transmission + Power shafts + Brake system + Suspension bracket and steering + Body and salon furnish + Onboard electric equipment 
|
Repair without extraction from the car of the petrol engine of 1.3 l Engine cross-sectionEngine longitudinal section Instructions for use a material of the Head The given Part of the Head is devoted repair of the petrol engine of 1.3 l, not connected with its extraction from the car (in situ). The description большей parts of considered procedures is made, proceeding from the assumption that the power unit remains on the regular place in an impellent compartment of the car. In view of told, in a case if the engine is already dismantled and established on a workbench or the assembly stand, many of described steps should be lowered. Let's notice that despite physical possibility of performance of repair in situ such components as shatunno-piston groups, this sort of works are usually made after dismantling of the engine in view of necessity of carrying out of some auxiliary procedures, not to mention requirements to observance of cleanliness of details and absolute passableness маслотоков. The general description of the engine The considered engine concerns family of 4-cylinder petrol engines with рядным placing of cylinders and the top arrangement of valves (OHV). Cross-section and longitudinal cuts of the engine are presented on illustrations. The engine is established cross-section in a forward part of the car and inclined forward at an angle 20 . Transmission and coupling assemblages are in the left part of the power unit. The block of cylinders, head and head cover are cast from an aluminium alloy. The bottom part of cylinders гильзуется loose leaves of pig-iron moulding. The bases of sleeves are equipped by sealing linings in order to avoid penetration of a cooling liquid into the pallet картера. The cranked shaft is established in three radical bearings. A flywheel with coupling assemblage fasten to a flange at the left end face of a shaft. The forward end of a cranked shaft is equipped by an asterisk for installation двухрядной chains of a drive of a camshaft. Radical and шатунные bearings have a demountable design and are equipped by two loose leaves. In the top head of a rod запрессована the bronze plug developed under landing of a piston finger. The right end of a camshaft is equipped by a spiral gear wheel of a drive of the distributor of ignition. The drive of the oil pump also is made from a camshaft through a distributor axis. The compulsory system of greasing of the engine is organised by means of шестеренчатого the pump taking away oil from the pallet картера through equipped mesh filter маслозаборник and submitting it to internal components of the engine, preliminary banishing through полнопоточный the oil filter of replaceable type established outside in a forward part of the block of cylinders. In spite of the fact that the engine is not высокооборотным and does not differ the big capacity, it provides to the car quite decent dynamic characteristics. Thanks to that the engine is not overloaded, under condition of use high-quality oil and fuel, it differs raised reliability and durability.
The list of the repair procedures, which performance does not demand extraction of the engine from the car Procedures of repair and the engine service which performance can be made in situ are more low listed: a) Removal and installation of a belt of a drive of auxiliary units; b) Removal and installation of a cover of a head of cylinders; c) Removal and assemblage installation коромысел; d) Removal and installation of a head of cylinders; e) Removal and installation of a cover of a chain of drive ГРМ; f) Removal and installation of a chain of drive ГРМ from asterisks; g) Removal and installation маслоохладителя; h) Removal and installation of the oil pump; i) Removal and pallet installation картера; j) Dekarbonizatsija of a head of cylinders and pistons; k) Replacement of epiploons of a cranked shaft; l) Removal, check of a condition and flywheel installation; m) Check of a condition and replacement of support of a suspension bracket of the power unit; |
|