Skoda Felicia

Since 1994 of release

Repair and car operation



Shkoda Felitsija
+ Cars of mark Skoda Felicia
+ The maintenance instruction
+ Routine maintenance
+ Engine repair
+ Systems of cooling, heating
+ The power supply system
+ Engine electric equipment
+ Coupling
+ Transmission
+ Power shafts
+ Brake system
+ Suspension bracket and steering
- Body and salon furnish
   The general information and safety measures
   Care of components of a body and the car bottom
   Care of an upholstery and carpet coverings of salon
   Repair of insignificant damages кузовных panels
   Repair seriously damaged кузовных panels
   Removal and installation of a forward bumper
   Removal and installation of a back bumper
   Removal, installation and cowl adjustment
   Removal and installation drive a cable отпускания the cowl lock
   Removal, installation and adjustment of assemblage of the lock of a cowl
   Removal and installation of doors
   Removal and installation of panels of an internal upholstery of doors
   Removal and installation of door handles and lock components
   Removal and installation of door glasses and regulators Glass lifts
   Removal and installation of a door of a back and its persistent bars
   Removal, installation and adjustment of components of the lock of a door of a back
   Removal and installation of components of the uniform lock
   Removal and installation of components of the electric drive Glass lifts
   Removal and installation of external rear-view mirrors and accompanying components
   Windscreen and glass of a door of a back - the general information
   The top hatch
   Removal and installation of elements кузовной furnish
   Removal and installation of seats
   The mechanism натяжителя a seat belt of a forward seat - the general information
   Removal and installation of components of seat belts
   Removal and installation of elements of furnish of salon
   Removal and installation of the central console
   Removal and installation of the panel of devices
   Control кузовные the sizes
+ Onboard electric equipment


c9b0dd5c

Removal and installation of the panel of devices

REMOVAL

 PERFORMANCE ORDER

Before an electroconducting detachment take care of its marks according to which at assemblage it will be carried out linings of plaits and connection of sockets

1. Remove the battery (see Has undressed Removal and installation of the storage battery).
2. Remove the central console (see Has undressed Removal and installation of the central console).
3. Remove a steering column (see Has undressed Removal, installation and adjustment of assemblage of the lock of a cowl).
4. Operating according to resulted in the Head Onboard электрооборудованиеуказаниями, remove following components:

a) the Instrument guard;
b) the Radio tape recorder;
c) Prikurivatel;
d) the Passenger pillow of safety (if that is provided).

5. Turn out a clamp and liberate the assembly block of safety locks/relays from the basis of the panel of devices from its passenger party.

6. Unbend lock uvulas and take bearing sled of a radio tape recorder from a reception nest in the panel of devices. Disconnect from assemblage of a sled an antenna cable and an electroconducting socket.

7. Accurately having hooked, remove the handle of the hydroproof-reader of an optical axis of head block headlights...

... On pair turns ослабьте fixing screws, then slightly turn a regulator of the proof-reader counter-clockwise and push it in the panel of devices.

8. On models without a passenger pillow of safety open a cover on the panel of devices, release clamps and take a ware box.

9. Turn out two fixing screws, located in an aperture under installation of an instrument guard. Also give one screw in a nest under installation of a ware box.

10. Moving along a bottom edge of the panel of devices, turn out all fixing screws located there.

11. In an impellent compartment give six nuts of fastening of the panel to a partition, remove washers (four nuts are located directly under a windscreen and two - below). Try to remember adjusting positions изоляционных the plates enclosed under four top nuts.

12. In salon of the car by means of the assistant separate the basis of the panel of devices from a partition of an impellent compartment, then lift assemblage upwards, removing it from the top fixing hairpins. Separate the panel from a partition and (correcting electroconducting plaits in apertures through passage) take it from the car.

INSTALLATION

 PERFORMANCE ORDER

Installation is made upside-down. Before fixture installation pass in appropriate apertures through passage all plaits and electroconducting cables. At the first stage the fixture is tightened only by hand. Then follows, moving on panel perimetre to tighten screws and nuts with demanded effort. In summary connect the battery and check up serviceability of functioning of all electric components and switches.