Skoda Felicia

1. Merge impellent oil (Routine maintenance see the Head).
2. Remove a belt of a drive of auxiliary units (see Has undressed Removal, installation and adjustment of a tension of a belt of a drive of auxiliary units).
3. Remove pulleys of an auxiliary belt and external covers газораспределительного a belt, then result the engine in position ВМТ of the end of a step of compression of the piston of the first cylinder and remove газораспределительный a belt and a cogwheel of a cranked shaft (Sections Reduction of the piston of the first cylinder in position of the top dead point (ВМТ) the end of a step of compression, Removal and installation of a belt of drive ГРМ and its covers see, Removal and installation натяжителя and cogwheels of a belt of drive ГРМ).

4. Drill in a face surface of an epiploon pair of small apertures and screw in them саморезы (try not to damage a wall of a nest and a surface of a pin of a shaft). Having grasped heads of screws flat-nose pliers, take an epiploon from a landing nest.

5. Without applying some any solvents, wipe pure неворсящейся rags of a wall of a nest of an epiploon and a surface of a pin of a shaft. Polish all agnails, teases and the roughnesses, capable to lead to failure of a new epiploon.
6. Grease sponges of a new epiploon and enclose it in a nest in a casing.
7. Hammer blows on оправке suitable diameter, запрессуйте an epiploon in a casing. In quality оправки the face head of the suitable size or a piece of a pipe of the corresponding diameter can be used. Оправка should rest exclusively against firm external edge of an epiploon.
8. Establish into place all components removed with a view of providing of access and adjust a tension of belts (Sections Reduction of the piston of the first cylinder in position of the top dead point (ВМТ) the end of a step of compression, Removal and installation of a belt of drive ГРМ and its covers see, Removal and installation натяжителя and cogwheels of a belt of drive ГРМ).
9. Fill in in the engine necessary quantity of engine oil of a demanded grade.

1. Execute the procedures, described paragraphs with 1 on 3, then remove the pallet картера (see Has undressed the Pallet - removal, check and installation).
2. In stages turn out bolts of fastening of a casing of an epiploon.
3. Vrashchatelno-progress accurately remove a casing in gathering with an epiploon from a pin of a cranked shaft.
4. Remove an old lining from an interfaced surface of the block of cylinders. Operating extremely cautiously, smooth out interfaced surfaces of a casing and the block of cylinders, completely having removed from them traces of a material of an old lining (take advantage of a scraper or a penknife).

5. In case of need take from the nest in a casing an old epiploon, accurately having hooked it for this purpose a screw-driver with a flat sting.

6. Carefully wipe a casing and check up it on presence of cracks and deformation signs interfaced surfaces. Lay a casing on a workbench, an interfaced surface downwards. If removed, запрессуйте in a landing nest a new epiploon, having pressed to it wooden брусок and tapping on the last with a hammer.

7. Grease an interfaced surface of the block of cylinders with universal hermetic and press to it a new lining of a casing.

8. Wind a pin of a cranked shaft with an adhesive tape.

9. Grease internal sponges of an epiploon with pure impellent oil, bring casing assemblage to the regular place on the block and vrashchatelno-progress plant it on a pin of a cranked shaft, densely having pressed to the block.

10. Screw bolts of fastening of a casing and in stages tighten them with demanded effort.

Remember that the casing is made of a soft aluminium alloy and can be easily damaged at a non-uniform tightening of bolts.

11. Establish into place the pallet картера (see Has undressed the Pallet - removal, check and installation).
12. Establish into place all other components removed for the purpose of providing of access, do not forget to adjust a tension of belts (Sections Reduction of the piston of the first cylinder in position of the top dead point (ВМТ) the end of a step of compression, Removal and installation of a belt of drive ГРМ and its covers see, Removal and installation натяжителя and cogwheels of a belt of drive ГРМ).
13. In summary fill in in the engine necessary quantity of engine oil of a demanded grade.

1. Execute the procedures described in paragraphs with 1 on 3, then remove the pallet картера (see Has undressed the Pallet - removal, check and installation).
2. Remove from the engine a transmission (the Transmission see the Head).
3. Remove a flywheel (see Has undressed the Flywheel - removal, check and installation), and also a frictional disk and assemblage of a basket of coupling (Coupling see the Head).
4. At a corresponding complete set turn out fixing bolts and remove from the block of cylinders an intermediate plate.
5. In stages ослабьте also turn out bolts of fastening of a casing of a back epiploon.
6. Vrashchatelno-progress accurately remove a casing in gathering with an epiploon from a shaft pin.
7. Remove from the block a lining and smooth out an interfaced surface.
8. The back epiploon varies in gathering with a casing and in an individual order is not delivered.

9. Grease with universal hermetic an interfaced surface of the block and establish on it a new sealing lining of a casing.

10. In the complete set to firm epiploons of manufacture of company Skoda the protective plastic plug is usually delivered, allowing to avoid epiploon damage about edges шпоночного a groove at assemblage putting on on a shaft pin. At installation of an epiploon of not firm manufacturing, wind a pin with an adhesive tape.

11. Grease internal sponges of a new epiploon with pure impellent oil, then vrashchatelno-progress accurately put on assemblage a pin, densely having pressed it to the block.

12. Screw fixing bolts and in stages in regular intervals tighten them with demanded effort. Remember that the casing is made of a soft aluminium alloy and can be easily damaged at a non-uniform tightening of bolts.

13. Establish the pallet картера (see Has undressed the Pallet - removal, check and installation).
14. Establish a frictional disk and assemblage of a basket of coupling (Coupling see the Head).
15. Establish into place a transmission (the Transmission see the Head).
16. In summary fill in in the engine necessary quantity of engine oil of a demanded grade (Routine maintenance see the Head).