Skoda Felicia

Since 1994 of release

Repair and car operation


Shkoda Felitsija
+ Cars of mark Skoda Felicia
+ The maintenance instruction
+ Routine maintenance
+ Engine repair
+ Systems of cooling, heating
+ The power supply system
+ Engine electric equipment
+ Coupling
+ Transmission
+ Power shafts
- Brake system
   The general information
   System design, the description of separate knots and mechanisms
   Prorolling of hydraulic system
   Replacement of hoses and tubes of a hydraulic path of brake system
   Replacement колодок disk brake mechanisms of forward wheels
   Replacement of boots of drum-type brake mechanisms of back wheels
   Condition check, removal and installation of disks of forward brake mechanisms
   Removal, check of a condition and installation of drums of brake mechanisms of back wheels
   Removal, major repairs and installation of supports of brake mechanisms of forward wheels
   Removal, major repairs and installation of wheel cylinders of back brake mechanisms
   Removal, major repairs and installation of the main brake cylinder (ГТЦ)
   Removal and installation of a pedal of a foot brake
   Check of serviceability of functioning, removal and installation of the vacuum amplifier of brakes
   Removal, check of a condition and installation of the control valve of the vacuum amplifier of brakes from a hose
   Adjustment of a lay brake
   Removal and installation of the lever of a lay brake
   Removal and installation of cables of a drive of a lay brake
   Check of serviceability of functioning, removal and installation of the valve-regulator of pressure in hydraulic contours of brake mechanisms of back wheels
   Removal, installation and adjustment of the gauge-switch of stoplights
   System of antiblocking of brakes (ABS) - the general information
   Removal and installation of components of systems ABS
   Removal and installation of the vacuum pump (diesel models)
   Check of a condition and major repairs of the vacuum pump (diesel models)
+ Suspension bracket and steering
+ Body and salon furnish
+ Onboard electric equipment

c9b0dd5c

Removal and installation of a pedal of a foot brake

Components of assemblage of a pedal of a foot brake

1 — the Returnable spring
2 — the Axial plug
3 — the Arm
4 — the Rubber washer
5 — the Gauge-switch of stoplights
6 — the Counternut
7 — the Lock clamp
8 — the Lock clamp

9 — the Rod of a pusher of the vacuum amplifier with a fastening plug to a pedal
10 — the Pedal of a foot brake
11 — a pedal Overlay
12 — the Washer
13 — the Nut (15 Nanometers)
14 — the Axis
15 — a coupling Pedal


Models with a right-hand steering

The brake pedal is united in uniform assemblage with a coupling pedal.

Despite the extremely limited access, it is provided replacements of axial plugs of a pedal without dismantle of all assemblage. Remove lock rings from both ends of an axis and liberate plugs from arms. Before installation it is necessary to grease new plugs with universal greasing of type Litol 24 or G000062. Track correctness of landing in the flutes of lock rings.

Models with a link sided steering

REMOVAL

 PERFORMANCE ORDER

1. Remove a coupling pedal.
2. Release a clamp and liberate from a pedal a tip of fastening of a rod of a pusher of the servo-driver of the vacuum amplifier of brakes.
3. Unhook from a pedal a returnable spring.
4. Take the axial plug and remove a pedal from a basic arm (together with a returnable spring).
5. Check up a pedal on presence of wear tracks or mechanical damages. It is necessary to give special attention to a condition of the axial plug. Defective components replace.

INSTALLATION

 PERFORMANCE ORDER

1. Grease a nest in pedals, the axial plug and a tip of fastening of a rod of a pusher with universal greasing of type Litol 24 or G000062
2. In the correct image connect to a pedal a returnable spring. Having tracked correctness of gearing in a pedal of a rod of a pusher of the servo-driver of the vacuum amplifier of brakes, plant on the regular place the axial plug.
3. Level a pedal concerning a pusher and fill into place a fixing tip. Fix a tip a clamp, having tracked correctness of landing of the last in the flute.
4. Connect a returnable spring to a pedal. Before installation of a pedal of coupling make sure in испрвности functioning of a foot brake.