Skoda Felicia

Since 1994 of release

Repair and car operation


Shkoda Felitsija
+ Cars of mark Skoda Felicia
+ The maintenance instruction
+ Routine maintenance
- Engine repair
   + Repair without extraction from the car of the petrol engine of 1.3 l
   - Repair without extraction from the car of the petrol engine of 1.6 l
      The description of the basic knots and mechanisms
      Reduction of the piston of the first cylinder in position of the top dead point (ВМТ) the end of a step of compression
      Check компрессионного pressure - an order of carrying out and interpretation of results
      Removal and installation of a belt of drive ГРМ and its covers
      Removal, check of a condition and installation of cogwheels and натяжителя a belt of drive ГРМ
      Removal, installation and adjustment of effort of a tension of a belt of a drive of auxiliary units
      Removal and installation of a cover of a head of cylinders
      Replacement of an epiploon of a camshaft
      Replacement of epiploons of a cranked shaft
      Removal and installation of a head of cylinders in gathering with the inlet pipeline and a final collector
      Check of serviceability of functioning of hydraulic pushers
      Removal, check of a condition and flywheel installation
      Check of a condition and replacement of support of the power unit
      Removal and pallet installation картера the engine
      Removal and installation of the oil pump and маслозаборника
   + Repair without extraction from the car of the diesel engine
   + Dismantle of the power unit and engine major repairs
+ Systems of cooling, heating
+ The power supply system
+ Engine electric equipment
+ Coupling
+ Transmission
+ Power shafts
+ Brake system
+ Suspension bracket and steering
+ Body and salon furnish
+ Onboard electric equipment

c9b0dd5c

Removal, check of a condition and flywheel installation

The general information

The flywheel is made of a steel and equipped by a gear wreath. Fastens to a flange of a cranked shaft six bolts М10х1 with heads of type TORX. The flywheel is calculated on installation of assemblage of coupling in diameter of 190 mm. Boltovye apertures are located asymmetrically that defines unambiguity of landing of the flywheel which balancing is made in gathering with cranked shaft. The carving part of bolts at assemblage is greased with fixing hermetic of type Loctite 574 or Loctite 270.

At installation of a gear wreath on a flywheel last is necessary for warming up to temperature 400С.

REMOVAL

 PERFORMANCE ORDER

1. Remove a transmission (the Transmission see the Head) and coupling assemblage (Coupling see the Head).

2. By means of the clamp made of a thick metal plate (see an accompanying illustration) jam a gear wreath of a flywheel, having blocked last from проворачивания in process отдавания bolts of its fastening. Alternatively the flywheel can be blocked by means of a metal plate, приболченной between it and a coupling dome. In order to avoid balancing infringement at assemblage mark flywheel position in relation to an end face of a pin of a cranked shaft

3. Turn out fixing bolts and by means of the assistant remove a heavy flywheel.

CHECK

 PERFORMANCE ORDER

1. Check up a condition interfaced to a disk of coupling of a surface of a flywheel. In case of revealing of deep scratches, cracks, задиров and other mechanical damages the flywheel is subject to replacement, or should be given in проточку (consult at experts of car-care centre).
2. Attentively examine a gear wreath of a flywheel. In case of deterioration or loss of teeths it is necessary to replace a wreath in the conditions of a car-care centre workshop.

INSTALLATION

 PERFORMANCE ORDER

1. Carefully smooth out interfaced surfaces of a flywheel and a pin of a cranked shaft. Having banished a tap carving apertures in an end face of a pin of a cranked shaft, remove from them the rests of fixing hermetic and corrosion products.

At absence of near at hand suitable tap of an aperture can be cleaned by means of an old bolt with sawn through along a carving part, like described in Section Replacement of epiploons of a cranked shaft (but with a head).

2. If new fixing bolts are not missed the mark by fixing structure on manufacturer, slightly grease their carving part with suitable hermetic.

3. Establish a flywheel on a pin of a cranked shaft according to the landing labels put in the course of dismantle.

The new flywheel can be established in any position. Screw bolts and tighten them, while only by hand.

4. One of offered above ways block a flywheel from проворачивания, then tighten fixing bolts with demanded effort.

5. Establish to the place of coupling and transmission assemblage (Heads Coupling and the Transmission see).